Cisco Codec C Series 시작하기 매뉴얼 - 페이지 30

{카테고리_이름} Cisco Codec C Series에 대한 시작하기 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco Codec C Series 32 페이지. Telepresence conference system
Cisco Codec C Series에 대해서도 마찬가지입니다: 시작하기 매뉴얼 (41 페이지), 사용자 설명서 (44 페이지), 시작하기 매뉴얼 (35 페이지), 시작하기 매뉴얼 (42 페이지), 시작하기 매뉴얼 (46 페이지)

페이지 인쇄
Cisco Codec C Series 시작하기 매뉴얼
Profile Series, Codec C Series and Quick Set C20 / C20 Plus
Contents
Introduction

Password protection

The system is password protected in the following ways:
•
The
Administrator settings menu
can be password
protected with a menu password.
•
The
Codec
is password protected. You always need to
enter a username to log in.
The same username and password is used for the web and
command line interfaces.
You can also configure the codec to prompt for a PIN-code
before accessing all the on screen menus.
»
The default username is
admin
with no password set.
NOTE:
We recommend that you set a password for the
admin
user - see how to

Change your codec password

to the right.
»
New user accounts with username and password/PIN-
code can be created using the web interface.
Read more about how to create users with passwords
and PIN codes in the Administrator guide for your
product.
•
You can protect the
File system
of the codec by setting a
password for the
root
user. The root user is disabled by
default.
NOTE:
When a new administrator password has been defined
make sure you keep a copy of the password in a safe place.
Contact your Cisco representative if you have forgotten the
password.
Profile Series, Codec C Series and Quick Set C20/C20 Plus Getting Started Guide TC4.1, Feb 2011.
D14639.03
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
Configure your system
Operating devices

Set the Administrator settings menu password

When you set a password for the Administrator settings menu,
all users must enter the password to get access to this menu,
either on screen when using a remote control, or on the touch
screen if you are using a Touch controller.
Set the menu password using the remote control
Perform the following steps to define a password for the
Administrator settings menu:
1.
In the on screen menu, go to Home > Settings >
Administrator settings > Set menu password.
The password format is a string with 0–255 characters.
2.
Enter the new password in the Set password menu.
3.
Press Save.
Perform the following steps to change the password for the
Administrator settings menu:
1.
To change the password, go to Home > Settings >
Administrator settings > Set menu password.
2.
Enter the new password in the Set password menu.
3.
Press Save.
Perform the following steps to deactivate the password for the
Administrator settings menu:
1.
To deactivate the password, go to Home > Settings >
Administrator settings > Set menu password.
2.
Leave the input field empty in the Set password menu.
3.
Press Save to save the blank password. This will deactivate
the Administrator settings menu password.
Set the menu password from a command line interface
Open a command line interface, for example PuTTY, and run
the following command:
xCommand SystemUnit MenuPassword Set
Password: <password>
30
The menu system
The web interface
Change your codec password
A user, including the default
password using the web
If a password is not currently set, use the procedure below
with a blank current password.
Change the password using the web interface
Perform the following steps to change the codec password:
1.
Log in to the web interface with your username and current
password.
2.
Go to the Change password page.
3.
Enter the current password, the new password, and repeat
the new password in the appropriate input fields.
The password format is a string with 0–255 characters.
4.
Click Save.
Getting started guide
Password protection
Password protection
admin
user, can change his codec
interface.
www.cisco.com