Cisco Codec C Series 시작하기 매뉴얼 - 페이지 15

{카테고리_이름} Cisco Codec C Series에 대한 시작하기 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco Codec C Series 46 페이지. Telepresence conference system
Cisco Codec C Series에 대해서도 마찬가지입니다: 시작하기 매뉴얼 (41 페이지), 사용자 설명서 (44 페이지), 시작하기 매뉴얼 (35 페이지), 시작하기 매뉴얼 (32 페이지), 시작하기 매뉴얼 (42 페이지)

페이지 인쇄

Cisco TelePresence Video Systems

Contents

Configuring H.323 and SIP

(When not set by a provisioning system)

To get online and ready to place and receive calls, your system

must be set up properly. Your system uses either the H.323

protocol or the SIP protocol for video calls.

NOTE:

Contact your system administrator, or service provider,

for information about the network settings.

For networks administered through Cisco TMS (TelePresence

Management Suite), your Cisco TMS administrator will help

you to get online.

You can find information about administering through Cisco UCM

in the

Administering TC endpoints on CUCM

Back to task overview

D14639.15 Video Systems Getting Started Guide TC7.2, OCTOBER 2014.

Introduction

User interfaces

H.323

If in doubt about any of the parameters below, contact your

system administrator or your service provider.

1. Tap the user name in the upper left corner and tap

> Administrator >

2. Enter the

input fields.

3. To enter the H.323 gatekeeper address manually, tap

Manual

in the

Gatekeeper Address

guide.

4. If the H.323 gatekeeper requires authentication and you

want your system to authenticate itself to the gatekeeper,

tap

in the

Otherwise, tap OFF.

5. Tap

Save

to confirm the changes, or

saving.

6. Review the System Information page and verify the H323

settings.

If you have successfully registered to the Gatekeeper, the

Status

is shown as

7. Tap

Exit

to return to the home menu.

Configuration

Settings

H323.

H323 Number

and

H323 Id

in their respective

Gatekeeper Discovery

section, and enter the

in the input field. Otherwise tap Auto.

Authentication Mode

section and enter the

and

Password

in their respective input fields.

Undo

to leave without

Registered

in the H323 section.

Getting Started Guide

Appendices

SIP

If in doubt about any of the parameters below, contact your

system administrator or your service provider.

1. Tap the user name in the upper left corner and tap

> Administrator >

SIP.

2. Enter the SIP URI in the

URI

input field.

3. Tap the preferred transport protocol in the

section. If you select Auto, the system first tries to connect

using TLS, then TCP, and finally UDP.

4. Select a

Proxy

Type. Step through the list of available

proxy types by tapping the - or + signs. The default type

is Standard.

5. To enter the SIP proxy address manually, tap

Proxy Discovery

section and enter the

input field. If you want the system to obtain the SIP proxy

address automatically (DHCP), tap Auto.

6. If the SIP proxy server requires authentication, you must

enter the

and

Password

in their respective input

fields to authenticate your system.

7. Tap

Save

to confirm the changes, or

saving.

8. Review the System Information page and verify the SIP

settings.

If you have successfully registered to a SIP server, the

Status

is shown as

Registered

in the SIP section.

9. Tap

Exit

to return to the home menu.

Contacts

Settings

Default Transport

Manual

in the

Proxy Address

in the

Undo

to leave without