Cisco DX series 시작하기 매뉴얼 - 페이지 16

{카테고리_이름} Cisco DX series에 대한 시작하기 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco DX series 34 페이지. Telepresence video systems

페이지 인쇄

Cisco TelePresence Video Systems



Introduction

IP settings

(When not set by a provisioning system)

Your video conference system supports IP version 4 (IPv4),

IP version 6 (IPv6) and Dual, which is the default setting. In all

three cases, the IP parameters can be assigned automatically

by the network, or you can set everything manually. When set

to Dual, the network interface can operate on both IP versions,

and have both an IPv4 and an IPv6 address.

If you wish to set the parameters manually, contact your

network administrator to obtain the required parameters.

If you choose to set the IP settings manually while using the

Dual mode, you have to set both the IPv4 and the IPv6 settings.

Start from step 2 in the instructions.

If your system is provisioned automatically, these IP settings

may be overridden by the provisioning system.

If an IPv4 or IPv6 address is already assigned to the system,

you can find it on the System Information page. Go to the

tab and choose

Status

and Network.

NOTE:

It is not recommended to manually change the IP

address using the web interface, or remotely paired Touch

controller.

If you are changing a value setting,

you have to always click

save

to confirm the change.

D15318.03 Video Systems Getting Started Guide CE8.2, JUNE 2016.

User interfaces

Web interface

To set or change the IPv4 settings

Go to the

Setup

Choose IP version

Click the

from the

Choose automatic or manual IP assignment

Scroll down the page to the

from the

IP assignment; or Static, if you wish to set the IP address

manually.

If you wish to set IP Assignment manually

In the

IPv4

SubnetMask

Scroll up to the

Setup

address in the

* IP Assignment:

DHCPv6: All IPv6 addresses, including options like the DNS and NTP

server addresses, are obtained automatically from a DHCPv6 server.

Autoconf: The system and gateway IP addresses will be assigned

automatically. The options, e.g. NTP and DNS server addresses, must be

set/assigned according to the DHCP Options setting. **

Static: The system and gateway IP addresses must be configured

manually. The options, e.g. NTP and DNS server addresses, must be set/

assigned according to the DHCP Options setting. **

Setup assistant

tab and click Configuration.

Network

settings in the left sidebar. Choose

IPStack

drop down list.

IPv4

section and choose

Assignment

drop down list, if you want automatic

section, enter the Address,

Gateway

in the corresponding input fields.

DNS

section and enter the DNS server

Server 1 Address

input field.

Touch

To set or change the IPv6 settings

Go to the

Setup

tab and click Configuration.

Choose IP version

IPv4

Click the

Network

settings in the left sidebar. Choose

from the

IPStack

drop down list.

Choose automatic or manual IP assignment

DHCP

Scroll down the page to the

DHCPv6,

Autoconf

Static

down list according to your network requirements.*

If IP Assignment is Static: Set the IP addresses

Enter the system IP address in the

and

Optional: Enter the gateway address in the

field.

If IP Assignment is Static or Autoconf: DHCPOptions

Choose

Off

from the

according to your network requirements.**

If DHCPOptions is Off: Configure DNS and NTP

Scroll up to the

DNS

section, and enter the DNS server

address in the

Server 1 Address

Open the

NetworkServices

and scroll down to the

NTP

address in the

Server 1 Address

Auto.

** DHCP Options:

On: The IP parameters, like the DNS and NTP server addresses, will be

obtained automatically from a DHCPv6 server.

Off: The IP parameters, like the DNS and NTP server addresses, must be

set manually.

Getting Started Guide

Appendices

IPv6

section and choose

from the

Assignment

drop

Address

input field.

Gateway

input

DHCPOptions

drop down list

input field.

settings from the left sidebar,

section. Enter the NTP server

input field. Set

Mode