Argo AW38AL 사용 설명서 - 페이지 11

{카테고리_이름} Argo AW38AL에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Argo AW38AL 12 페이지. Split air conditioner system
Argo AW38AL에 대해서도 마찬가지입니다: 사용 설명서 (12 페이지)

페이지 인쇄

AIR FILTER

The filter behind the air intake grille should be checked and cleaned

when the filter lamp lights up (see page 3).

HOW TO REMOVE THE FILTER

Air intake grille

1. Grasp both ends of the air intake grille and pull it towards you

and up.

2. Push the filter up slightly, and then pull it down.

FILTER CLEANING

Use a vacuum cleaner to remove light dust. If there is sticky dust

on the filter, wash the filter in lukewarm, soap water, rinse it in

clean water, and dry it.

HOW TO REPLACE THE FILTER

Insert into the groove on the unit

1. With the «FRONT» mark facing you, slide the filter up

into the unit and then lower the handler into the groove

on the unit.

2. After installing the filter, press the locations marked by

the arrows ( ) and close the air intake grille.

3. Press the RESET button to turn off the filter lamp (see

page 3).

TIPS FOR ENERGY SAVING

DO NOT:

Block the air intake and outlet of the unit.

If they are obstructed, the unit will not work well, and may be

damaged.

Let direct sunlight into the room. Use sunshades, blind or

curtain.

DO:

Always try to keep the anti-mold filter clean. A clogged filter will

impair the performance of the unit.

To prevent conditioned air from escaping, keep windows, doors

and any other openings closed.

TROUBLESHOOTING

WARNING

The use of portable telephones near the air-conditioner may cause

disturbance to its normal operation and must be avoided. In case

abnormal operation is noticed, to restore normal operation turn-

off electric supply for 60 seconds at least, by disconnecting the

main switch or the wall plug, then start again the air conditioner.

If your air conditioner does not work properly, first check the

following points before requesting service.

If it still does not work properly, contact your dealer or service

centre.

Trouble: the air conditioner does not run at all.

Air filter

Possible cause:

1. Power failure.

2. Leakage breaker tripped.

3. Line voltage is too low.

4. Operation button on the remote control is OFF.

5. Batteries of the remote control unit have run down.

Remedy:

1. Restore power.

2. Contact service centre.

3. Consult your electrician or dealer.

4. Press the ON/OFF button on the remote control.

5. Replace batteries.

Trouble: The air conditioner does not operate and STANDBY

lamp flashes.

Possible cause:

1. Defective sensor.

Remedy:

Air intake grille

1. Contact service centre.

Trouble: TIMER lamp flashes and the air conditioner does not

operate.

Possible cause:

1. power failure during timer operation.

Remedy:

Air filter

1. Press ON/OFF button on remote control.

Trouble: Compressor runs but soon stops.

Possible cause:

1. Obstruction in front of condenser coil.

Remedy:

1. Remove obstruction.

Trouble: Poor cooling or heating performance.

Possible cause:

1. Dirty or clogged air filter.

2. Heat source or many people in room.

3. Doors and/or windows are open.

4. Obstacle near air intake or air discharge port.

5. Thermostat is set too high (for cooling) or too low (for heating).

6. Outdoor temperature is too low (heat pump version).

7. Defrosting system does not work (heat pump version).

Remedy:

1. Clean air filter to improve airflow.

2. Eliminate heat source if possible.

3. Shut them to keep the heat or cold out.

4. Remove it to ensure good airflow.

5. Set the temperature lower (or higher).

6. Try to use a back-up heater.

7. Consult your dealer.

Trouble: Clicking sound is heard from the air conditioner.

Possible cause:

1. In heating or cooling operation, any plastic parts may expand

or shrink due to a sudden temperature change. In this event,

a clicking sound may occur.

Remedy:

1. This is normal, and the sound will disappear when an even

temperature is settled.