Installing Cisco TelePresence System Profile 42"/52"
4
Wall mounting the unit
WARNING
Due to the size and weight of this equipment,
it is very important that the wall mount unit is
safely installed according to the installation
instructions and that the wall is able to safely
support the product.
It is highly recommended that the wall
mounted system is installed by trained
personnel.
1.
Use the Allen key, which is found in the
foot module box, when fastening the wall
brackets to the bottom module with four
M6×10 screws.
2.
Place the bottom module by the wall, mark
where to fasten the brackets and move the
bottom module away.
NOTE:
Use a level to make sure the system
is mounted in an upright position. Add a
spacer between the wall bracket and the
wall if necessary.
3.
Add the suitable fixing
device for the screws
in the wall.
4.
Open the rear door and locate and connect
the cables which are lead out of the system
at the rear side (the door is not accessible
when placed by the wall).
5.
Place the bottom module by the wall and
fasten it to the wall with proper screws.
Cables
8
Mounting the camera
1.
Connect the RJ45 cable to the camera (A1 or A2).
2.
Connect the HDMI cable to the camera (only valid for
A1, i.e. the PrecisionHD 1080p camera).
3.
Loosen the wing nuts on the camera bracket and move
RJ45
HDMI
the bracket to the rear position.
4.
Place the camera on the bracket and slide the bracket
with the camera towards the front.
Gently pull the cables down from inside the column to
5.
organize the cables.
6.
Tighten the wing nuts on the bracket.
Close the top cover.
7.
* For countries with 60 Hz current frequency you must set the PrecisionHD 1080p camera DIP switch to: 00100.
78-19778-01 Profile 42-52 Installation Sheet | December 2010 | © 2010 Cisco Systems, Inc. All rights reserved.
5
Unpack the Monitor box and mount the monitor to the bottom module
Speaker grille
Unpack the
monitor box.
Lift out to open
the snap lockers.
1.
Lift out to unlock and remove the snap lockers.
2.
Lift up the monitor cover to unpack the monitor.
3.
Locate the speaker grille.
4.
Carefully lift out the monitor and place it onto the bottom
module. It is recommended to be two persons for this operation.
5.
Insert the two M8×60 screws through the orange holes in
the speaker box.
6.
Tighten the monitor gently to the bottom module until the
monitor cannot be moved anymore.
A1
PrecisionHD 1080p*
RJ45
Push the camera
towards the front.
A2
PrecisionHD
EXTRA
12V DC IN
CAMERA
POWER
Wing nuts
6
Connect the monitor cables
Locate the cables in the bottom module and connect
them as described in the illustration:
1.
HDMI cable
2.
15 pin D-SUB cable
3.
Power cable
Power
HDMI 1
A 级声明( A Class product declaration)
本产品为 A 级 ITE，在其使用说明,铭牌等显著位置中已包含如下内
容的声明(We declare here that the subject product is A Class ITE
product, and the following statement is clearly marked in the user
manual and nameplate ：
A Class declaration
此为 A 级产品，在生活环境中，该产品可能会造成无线电干扰。在这
种情况下，可能需要用户对其干扰采取切实可行的措施。
WARNING:
WARNING
This is a class A product. In a domestic environment this product may cause radio
This is a class A product. In a domestic environment this product may
interference in which case the user may be required to take adequate measures.
cause radio interference in which case the user may be required to take
9
Finishing up
adequate measures.
1.
Use the levelling adjustment tool to adjust the height
声明所在位置
of the system to make it stable (stand-alone foot
module only).
Position of the Declaration： nameplate □
2.
Remove the plastic cover in front of the monitor.
3.
Remove the plastic foil on the monitor frame.
4.
Snap on the speaker grille to the front.
Use the supplied cloth to clean the system.
5.
HDMI
HD
HD
RJ45
KENSINGTON
VIDEO OUT
VIDEO OUT
LOCK
HDMI
CODEC
Rev. Date
Prep.
Checked Change
Telecom AS
117324 rev.
TANDBERG Aquarius 52"
3D CAD model file 117324 rev. 00E+ is master
Page 2
7
Camera cables
1.
Open the top cover.
2.
Push the camera cables up the
channel inside the monitor.
D-SUB 15
声 明
* The HDMI cable is only valid for the PrecisionHD 1080p camera.
10
Connect the system
1.
Open the rear door and route the cables out through the opening at the
lower part of the door.
2.
Close the rear door carefully.
User manual □
Place the microphones on the table, connect the microphone cables
3.
and place the PC cable on the table.
4.
Connect the Ethernet cable.
Connect the power cable, use the country specific power cable that
5.
came with the system.
公司 Company Name：
6.
Open the front door and turn on the monitor.
签字/盖章 Signature/ Stamp：
Follow the instructions in the accompanying Touch Screen CS
7.
installation guide to connect and initialize the touch screen.
LEVELLING ADJUSTMENT
8.
The system should be up and running in a few minutes.
Place the orange level
adjustment tool on the foot
wheel under the foot module
for height adjustment.
Seen from above, turn
clockwise to adjust the
height up. Use the opposite
side of the tool and turn
counterclockwise to adjust
down.
Sheet 1 of 1
Processes
Tolerances
Specification:
Material
Surface treatment
-
Type:
-
-
European
-
Manufacturer:
-
-
projection
-
Type number:
-
-
Thickness:
-
-
Unit:
mm
Dimensions without paint or finish
Color:
-
-
Sheet size:
A3
All materials, finishes, and proccesses
Surface:
-
-
must comply with the RoHS directives
Glossiness:
-
-
Scale:
1:20
Flame class:
-
-
Part weight:
85203g
Flame class requirement: -
UL reference:
-
-
RJ45
HDMI*
The rear door
Ethernet cable
PC cable
Microphone cables
Power cable
페이지 인쇄