Cisco TelePresence Video Systems
Contents
Configuring IP
(when not set by a provisioning system)
Your video conference system supports both iP version 4
(iPv4) and iP version 6 (iPv6). in both cases, the iP param-
eters can be assigned automatically by the network, or you
can set everything manually.
if you want to set the parameters manually please contact
your network administrator to obtain the required parameters.
if your system is provisioned automatically, these iP settings
may be overridden by the provisioning system.
if an iPv4 or iPv6 address is already assigned to the system, you
will find it on the System information page. Go to
tab and choose
System
Information.
NoTe:
You must restart the system after changing the iP
settings for the changes to take effect.
If you are changing a value setting,
you have to always click
save
to confirm the change.
Back to task overview
D14639.09 Video Systems Getting Started Guide TC6.1, April 2013.
Introduction
User interfaces
To set or change the IPv4 settings
Go to the
Configuration
1. Choose IP version
Click the
Network
Settings
choose IPv4 in the
2. Choose automatic or manual IP assignment
Choose DHCP in the
want automatic iP assignment; or Static if you want to set
the iP addresses manually.
Diagnostics
3. If IP Assignment is Static: Set the IP addresses
a. Scroll down the page to the
the Address,
sponding input fields.
b. Scroll up to the
address in the
* iP Assignment:
dHCPv6: All iPv6 addresses, including options, are obtained automatically
from a dHCPv6 server.
Autoconf: the system and gateway iP addresses will be assigned
automatically. the options, e.g. NtP and dNS server addresses, must be
set/assigned according to the dHCP options setting. **
Static: the system and gateway iP addresses must be configured manually.
the options, e.g. NtP and dNS server addresses, must be set/assigned
according to the dHCP options setting. **
Confirguration
Configuration
tab and choose
System
Configuration.
settings in the left sidebar. under
General
IPStack
drop down list.
Assignment
drop down list if you
IPv4
section and enter
Gateway
and
SubnetMask
in the corre-
DNS
section and enter the dNS server
Server 1 Address
input field.
25
Getting Started Guide
Appendices
To set or change the IPv6 settings
Go to the
Configuration
tab and choose
1. Choose IP version
Click the
Network
settings in the left sidebar. under
Settings
choose IPv6 in the
IPStack
2. Choose automatic or manual IP assignment
Scroll down the page to the
IPv6
DHCPv6, Autoconf or Static in the
Assignment
list according to your network requirements.*
3. If IP Assignment is Static: Set the IP addresses
enter the system iP address in the
Address
the gateway address in the
Gateway
4. If IP Assignment is Static or Autoconf:
DHCPoptions
Choose on or off in the
DHCPOptions
according to your network requirements.**
5. If DHCPoptions is off: Configure DNS and NTP
a. Scroll up to the
DNS
section and enter the dNS server
address in the
Server 1 Address
b. open the
NetworkServices
sidebar and scroll down to the
the NtP server address in the
Set
Mode
to Auto.
** dHCP options:
on: the iP parameters, like the dNS and NtP server addresses, will be
obtained automatically from a dHCPv6 server.
off: the iP parameters, like the dNS and NtP server addresses, must be
set manually.
Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved.
Contacts
System
Configuration.
General
drop down list.
section and choose
drop down
input field and
input field.
drop down list
input field.
settings from the left
NTP
section. enter
Address
input field.
페이지 인쇄