Cisco TelePresence MX300 시작하기 매뉴얼 - 페이지 14
{카테고리_이름} Cisco TelePresence MX300에 대한 시작하기 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco TelePresence MX300 42 페이지. Telepresence c series
telepresence mx series
telepresence sx series
telepresence ex series
Cisco TelePresence MX300에 대해서도 마찬가지입니다: 매뉴얼 (2 페이지), 빠른 참조 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (12 페이지), 빠른 참조 매뉴얼 (2 페이지), 문제 해결 매뉴얼 (37 페이지), 시작하기 매뉴얼 (46 페이지)
페이지 인쇄
Cisco TelePresence Systems
GettinG started Guide
Table of contents
Introduction
touch controller
Configuring IP
(when not set by a provisioning system)
Your video conference system supports both IP
version 4 (IPv4) and IP version 6 (IPv6).
In both cases, the IP parameters can be assigned
automatically by the network, or you can set everything
manually.
If you want to set the parameters manually please
contact your network administrator to obtain the
required parameters.
If an IP address is already assigned to your system, you
will find the current IPv4 and/or IPv6 address on the
System Information page:
Tap
More > Settings > System
Information.
The IPv4 Address and/or IPv6 Address of the system
is shown in the NETWORK section.
Back to task overview
D14639.06 Video Systems Getting Started Guide (TC5.1) | 2012 FEBRUARY | © 2011-2012 Cisco Systems, Inc. All rights reserved.
User interfaces
Configuration
Configuration
1. Select IP version
i. Tap
More > Settings > Administrator Settings > Network
Settings.
ii. Tap
IPv4
or
IPv6
in the
IP Version
requirement.
iii. Tap
Save
to save the change, or
Undo
2. Select automatic or manual IP assignment
i. Tap
Auto
in the
IP Assignment
section if you want
automatic IP assignment; or
Manual
IP addresses manually.
ii. Tap
Save
to save the change, or
Undo
IP Version
The IP configuration is complete.
IPv4
a. Tap
On
or
Off
according to your preference.
b. Tap
Save
to save the change, or
leave without saving.
IPv6
DHCP Options:
1
Off: All IP parameters, except the IP address and gateway, must be set manually.
Please refer to the Administrator Guide for your product for details about all settings.
On: The IP parameters, like the DNS and NTP server addresses, will be obtained automatically from the network.
Appendices
3. Set the IP addresses
Set the remaining IP settings according to the table below.
The actions required depend on the IP version and IP
assignment method you selected in the previous steps.
section according to your
4. Return to the main menu
to leave without saving.
Press
if you want to set the
to leave without saving.
IP Assignment
Auto
in the
DHCP Options
section
1
Undo
to
Exit
to return to the home menu.
Manual
a. Enter the
IP
Address,
Subnet
Mask, Gateway,
and
DNS Server
address. A soft keyboard
appears when you tap an input field
b. Tap
Save
to save the changes, or
Undo
leave without saving.
a. Enter the
IP Address
and Gateway. A soft
keyboard appears when you tap an input field.
b. Tap
On
or
Off
in the
DHCP Options
section
according to your preference.
1
c. Tap
Save
to save the changes, or
Undo
leave without saving.
www.cisco.com
14
to
to