Cisco TelePresence MX300 시작하기 매뉴얼 - 페이지 21
{카테고리_이름} Cisco TelePresence MX300에 대한 시작하기 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco TelePresence MX300 42 페이지. Telepresence c series
telepresence mx series
telepresence sx series
telepresence ex series
Cisco TelePresence MX300에 대해서도 마찬가지입니다: 매뉴얼 (2 페이지), 빠른 참조 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (12 페이지), 빠른 참조 매뉴얼 (2 페이지), 문제 해결 매뉴얼 (37 페이지), 시작하기 매뉴얼 (46 페이지)
페이지 인쇄
Cisco TelePresence Systems
GettinG started Guide
Table of contents
Introduction
remote control and on-screen menu
Configuring H.323 and SIP
(when not set by a provisioning system)
To get online and ready to place and receive calls, your
system must be set up properly. Your system will use either
the H.323 protocol or the SIP protocol for video calls.
NoTE:
Contact your system administrator, or service
provider, for information about the network settings.
For networks administered through Cisco TMS (Cisco
TelePresence Management Suite) your Cisco TMS
administrator will help you to get online.
Save the new value when you change a setting
• Drop down list selection: Navigate to the correct
value and press the
OK
( )
key to save, or press
the left arrow key
to leave without saving.
• Text entry in an input field: Enter the text, navigate
to
Ok/Save
to save the change, or navigate to
Cancel
to leave without saving; then press the
OK
( ) key
to confirm.
Back to task overview
D14639.06 Video Systems Getting Started Guide (TC5.1) | 2012 FEBRUARY | © 2011-2012 Cisco Systems, Inc. All rights reserved.
User interfaces
Configuration
Configuration
H.323
If in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Go to
Home > Settings > Administrator settings >
Advanced configuration > H323 > Profile
2. Go to
H323Alias
and enter the
the corresponding input fields.
3. If you want the system to obtain the H.323 gatekeeper
address automatically, go to
in the
Discovery
drop down list; if you want to enter the
address manually, select
Manual.
If set to
Manual
enter the gatekeeper address in the
Address
input field.
4. If the H.323 gatekeeper requires authentication and
you want your system to authenticate itself to the
gatekeeper, go to
Authentication
Mode
drop down list; otherwise select
If set to
On
enter the
LoginName
corresponding input fields.
5. Go to
Home > Settings > System information
the H323 settings.
If you successfully registered to the Gatekeeper the
Status
will show
Registered
in the H323 section.
6. Press
Home
(
)
to exit.
Please check the Administrator guide for your product if you
want to change the other H.323 settings.
Appendices
SIP
If in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Go to
1.
Advanced configuration > SIP > Profile
E164
number and
ID
in
2. Go to
input field.
3. Select your preferred
Gatekeeper
and select
Auto
drop down list. If you select
to connect using TLS, then TCP, and finally UDP.
4. Select your preferred proxy
The default type is Standard.
5. Go to
proxy address automatically, select
drop down list; if you want to enter the address manually,
and select
On
in the
select Manual.
Off.
If set to
and
Password
in the
input field.
6. If the SIP proxy requires authentication you must enter a
and verify
login name and password to authenticate your system.
Go to
Password
7. Go to
the SIP settings.
If you successfully registered to a SIP server the
will show
8. Press
Please check the Administrator guide for your product if you
want to change the other SIP settings.
Home > Settings > Administrator settings >
1.
URI
and enter the SIP URI in the corresponding
Default Transport
protocol in the
Auto
the system will first try
Type
in the drop down list.
Proxy 1.
If you want the system to obtain the SIP
Auto
in the
Discovery
Manual
enter the proxy address in the
Address
Authentication 1
and enter the
LoginName
in the corresponding input fields.
Home > Settings > System information
and verify
Registered
in the SIP section.
Home
(
)
to exit.
www.cisco.com
21
and
Status