Sony 10001 설치 매뉴얼 - 페이지 30
{카테고리_이름} Sony 10001에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sony 10001 50 페이지. A/v multiplexer board, a/v demultiplexer board
Sony 10001에 대해서도 마찬가지입니다: 설치 매뉴얼 (28 페이지)
페이지 인쇄
1-15. Removing/Reattaching Plug-in Boards
1-15. Removing/Reattaching Plug-in
Boards
n
When the plug-in board is replaced, refer to the mainte-
nance manual, volume-1.
1. Turn off the power.
2. Fully loosen the three fixing screws.
3. Remove the upper lid by moving in the direction
indicated by the arrow.
4. To remove the board retainer (L) or (S), loosen the
screw of it.
Screws with stopper
Upper lid
Screw
Protrusion
(with stopper)
Board retainer (L)
Square hole
5. Open the eject levers on the board to the direction of
the arrows.
6. Hold the eject levers and slowly pull the board out.
2
1
1
Pulling out
1-24
Screw with stopper
Screw
(with stopper)
Board retainer (S)
Protrusion
Sqauare hole
1
1
3
3
2
Insertion
7. When removing the EQ-75 or SDI-41 board, discon-
nect the harnesses from the following connectors on its
board.
EQ-75 board
CN100 (B-7) ........................... 6P White
CN500 (A-4) .......................... 4P White
CN600 (G-3) .......................... 4P Red
CN1500 (A-5) ........................ 4P Black
CN1600 (G-5) ........................ 4P Yellow
SDI-41 board
*1
*2
CN100
(C-1/A-1
) ............. 1P Red
*1
*2
CN101
(A-1/B-1
) ............. 1P Yellow
*2
CN700 (E-1/F-1
) ................. 1P Green/Orange
*2
CN701 (D-1/E-1
) ................ 1P Orange/Green
*2
CN800 (F-1/G-1
) ................. 1P Blue
*1: DNW-75/75P only
*2: At the suffix -11 or -21
*3: At the suffix -11, -21, or -13
When removing the DPR-118 board with BKNW-118
(DPR-119 board) disconnect the two cables from the
following connectors on the DPR-119 board.
DPR-119 board
CN1 ........................................ 1P Orange
CN3 ........................................ 1P Green
When removing the DPR-150 board of BKNW-124,
disconnect the two cables from the following connec-
tors on the DPR-150 board or the piggybacked DIF-
109 board onto the DPR-150 board.
DPR-150 board (DIF-109 board)
CN200 .................................... 1P Orange
CN201 .................................... 1P Green
When reattaching the board, install in the reverse order of
removal.
m
. After inserting the board, push the two eject levers
simultaneously to firmly connect the plug-in board to the
connector on the motherboard.
. When reattaching the board retainer, insert the protrusion
of the board retainer in the square hole on the chassis,
and then tighten the screw.
*3
*3
DNW-75/75P
DNW-65/65P