Cisco TelePresence SX20 시작하기 매뉴얼 - 페이지 18

{카테고리_이름} Cisco TelePresence SX20에 대한 시작하기 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco TelePresence SX20 46 페이지. In-room control on touch 10
Cisco TelePresence SX20에 대해서도 마찬가지입니다: 빠른 설정 (8 페이지), 시작하기 매뉴얼 (41 페이지), 시작하기 매뉴얼 (42 페이지), 빠른 참조 매뉴얼 (2 페이지), 빠른 설정 (2 페이지), 빠른 참조 매뉴얼 (2 페이지), 사용자 설명서 (34 페이지), 사용자 설명서 (29 페이지), 문제 해결 매뉴얼 (37 페이지), 규정 준수 및 안전 정보 매뉴얼 (9 페이지), 설정 매뉴얼 (8 페이지), 사용자 설명서 (38 페이지), 설치 매뉴얼 (2 페이지), 사용자 설명서 (2 페이지), 빠른 참조 매뉴얼 (2 페이지), 사용자 설명서 (37 페이지), 매뉴얼 (45 페이지), 매뉴얼 (45 페이지), 설치 시트 (2 페이지), 설치 매뉴얼 (2 페이지), 사용자 설명서 (34 페이지), 사용자 설명서 (5 페이지), 사용자 설명서 (38 페이지), 사용자 설명서 (38 페이지), 시작하기 매뉴얼 (42 페이지), 참조 매뉴얼 (8 페이지)

페이지 인쇄

Cisco TelePresence Video Systems

Contents

Provisioning set-up

(When using a provisioning system)

If in doubt for any of the parameters below, contact your provi-

sioning system provider.

See the administrator guide for your product to find more infor-

mation about the provisioning settings.

Select provisioning infrastructure

Go to

Home > Settings > Administrator settings > Advanced

configuration > Provisioning > Mode

and select a provisioning

infrastructure:

• TMS – Cisco TelePresence Management System

• Callway – WebEx Telepresence

• CUCM – Cisco Unified Communications Manager

• VCS - Cisco Video Communication Server

• Auto - The system starts provisioning by first trying VCS,

then TMS and finally CUCM.

• Edge - Cisco UCM via Expressway

If you select Off, all configurations must be set manually on the

video system.

Always save the new value when you change a setting

• Drop down list selection: Navigate to the correct value

and press the

( ) key to save, or press the left arrow

key

to leave without saving.

• Text entry in an input field: Enter the text, navigate to

Ok/Save

to save the change, or navigate to

to leave without saving; then press the

confirm.

Back to task overview

D14639.15 Video Systems Getting Started Guide TC7.2, OCTOBER 2014.

Introduction

User interfaces

Set the required provisioning parameters

Which parameters to set depends on which infrastructure was selected.

TMS

1. Go to

ExtermalManager

name of the Cisco TMS server in the

2. Enter the

Path

ing input field.

3. It may be required to authenticate the video system with

Cisco TMS. If so, go back to

LoginName

WebEx Telepresence (formerly Callway)

Upon ordering the Cisco WebEx Telepresence service, you have

received a

Video number

Please contact your company's WebEx Telepresence adminis-

trator, if you do not have a video phone number and an activation

code.

1. Enter the Video number in the

2. Enter the Activation code in the

CUCM

Go to

ExtermalManager

of the UCM provisioning server in the

You can find more details about setting up Cisco UCM provi-

sioning in the

NOTE:

If you wish to use Secure Mode for CUCM provisioning,

you must set it up on the web interface.

Cancel

( ) key to

Configuration

and enter the IP address or DNS

Address

input field.*

to the provisioning service in the correspond-

Provisioning,

and enter

and

Password

in the respective input fields.

and an

Activation

code.

LoginName

input field.

Password

input field.

and enter the IP address or DNS name

Address

input field.*

Administering TC endpoints on CUCM

Appendices

VCS

1. It may be required to authenticate the video system with

the Cisco VCS. If so, enter

respective input fields.

2. Go to

ExtermalManager

name of the Cisco VCS in the

the heading.

3. Enter the SIP

Domain

for the Cisco VCS in the correspond-

ing input field.

Have a look at the

Cisco VCS provisioning

information about VCS provisioning.

Cisco UCM via Expressway

Upon ordering Cisco UCM via Expressway service, you have

received a username, password, and domain name.

1. Enter the username in the

2. Enter the password in the

3. Navigate to

ExternalManager > Domain

domain name.

In some cases, you must manually enter the Expressway

address. Go to ExternalManager, and enter the address you

have received upon ordering in the

guide.

* The DHCP server can be set up to provide the External Manager address

automatically (Option 242 for TMS; Option 150 for UCM). Any input set up

here overrides the setting provided by DHCP.

Getting Started Guide

Contacts

LoginName

and

Password

in the

and enter the IP address or DNS

Address

input field under

appendix for more

LoginName

input field.

Password

input field.

and enter your

Address

input field.