Cisco TelePresence System C20 Plus 시작하기 매뉴얼 - 페이지 23
{카테고리_이름} Cisco TelePresence System C20 Plus에 대한 시작하기 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco TelePresence System C20 Plus 35 페이지. Telepresence conference system
Cisco TelePresence System C20 Plus에 대해서도 마찬가지입니다: 사용자 설명서 (44 페이지), 시작하기 매뉴얼 (32 페이지), 시작하기 매뉴얼 (46 페이지)
페이지 인쇄
Cisco TelePresence Systems
GettinG started Guide
Table of contents
Introduction
remote control and on-screen menu
Configuring H.323 and SIP
To get online and ready to place and receive calls, your
system must be set up properly. Your system will use either
the H.323 protocol or the SIP protocol for video calls.
NOTE:
Contact your system administrator, or service
provider, for information about the network settings.
For networks administered through Cisco TMS (Cisco
TelePresence Management Suite) your Cisco TMS
administrator will help you to get online.
Save the new value when you change a setting
• Drop down list selection: Navigate to the correct
value and press the
OK
( )
key to save, or press
the left arrow key
to leave without saving.
• Text entry in an input field: Enter the text, navigate
to
Ok/Save
to save the change, or navigate to
Cancel
to leave without saving; then press
OK
( )
to confirm.
D14639.04 Video Systems Getting Started Guide (TC4.2) | 2011 JULY | © 2011 Cisco Systems, Inc. All rights reserved.
User interfaces
Configuration
Configuration
H.323
If in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Go to
Home > Settings > Administrator settings >
Advanced configuration > H323 > Profile
2. Go to
H323Alias
and enter the
the corresponding input fields.
3. If you want the system to obtain the H.323 gatekeeper
address automatically, select
discovery
drop down list; if you want to enter the
address manually, select
Manual.
If set to
Manual
enter the
Gatekeeper address
corresponding input field.
4. If the H.323 gatekeeper requires authentication and
you want your system to authenticate itself to the
gatekeeper, select
ON
in the
Authentication mode
down list; otherwise select
OFF.
If set to
On
enter the
Login name
corresponding input fields.
5. Go to
Home > Settings > Administrator settings >
System Information
and verify the H323 settings.
If you successfully registered to a Gatekeeper the
will show
Registered
in the H323 section.
6. Press
Home
(
)
to exit.
Please check the
Administrator guide
want to change the other H.323 settings.
Appendices
SIP
If in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Go to
1.
SIP Settings > Profile
E164 number
and
Id
in
2. Go to
input field.
3. Select your preferred
Auto
in the
Gatekeeper
drop down list. If you select
to connect using TLS, then TCP, and finally UDP.
4. Select your preferred proxy
in the
The default type is Standard.
5. Go to
SIP proxy address automatically, select
Proxy discovery
drop
address manually, select Manual.
If set to
and
Password
in the
corresponding input field.
6. If the SIP proxy requires authentication you must enter a
login name and password to authenticate your system.
Go to
Status
Password
7. Go to
System Information
If you successfully registered to a SIP server the
for your product if you
will show
8. Press
Please check the
want to change the other SIP settings.
Home > Settings > Administrator settings >
1.
URI
and enter the SIP URI in the corresponding
Default transport
protocol in the
Auto
the system will first try
Type
in the drop down list.
Proxy 1.
If you want the system to obtain the
Auto
in the
drop down list; if you want to enter the
Manual
enter the
Proxy address
in the
Authentication 1
and enter the
LoginName
in the corresponding input fields.
Home > Settings > Administrator settings >
and verify the SIP settings.
Registered
in the SIP section.
Home
(
)
to exit.
Administrator guide
for your product if you
www.cisco.com
23
and
Status