Cisco TelePresence System Codec C90 매뉴얼 - 페이지 20
{카테고리_이름} Cisco TelePresence System Codec C90에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco TelePresence System Codec C90 25 페이지. Telepresence system
Cisco TelePresence System Codec C90에 대해서도 마찬가지입니다: 사용자 설명서 (44 페이지), 시작하기 매뉴얼 (42 페이지), 문제 해결 매뉴얼 (37 페이지), 설치 매뉴얼 (2 페이지), 사용자 설명서 (48 페이지), 시작하기 매뉴얼 (46 페이지)
페이지 인쇄
Cisco TelePresence System Codec C90
Contents
Audio signal levels,
cont...
Line outputs 1 to 4
Female RCA/phone
Signal
Absolute max
Nominal
levels
output level
level
Level
setting
[dB]
[Vpp]
[dBu]
[dBu]
-24.0
1,1
-6.0
-23.0
1,2
-5.0
-22.0
1,4
-4.0
-21.0
1,5
-3.0
-20.0
1,7
-2.0
-19.0
1,9
-1.0
-18.0
2,2
0.0
-17.0
2.5
1.0
-16.0
2.8
2.0
-15.0
3.1
3.0
-14.0
3.5
4.0
-13.0
3.9
5.0
-12.0
4.4
6.0
-11.0
4.9
7.0
-10.0
5.5
8.0
-9.0
6.2
9.0
-8.0
6.9
10.0
-7.0
7.8
11.0
-6.0
8.7
12.0
-5.0
9.8
13.0
-4.0
11.0
14.0
-3.0
12.3
15.0
-2.0
13.8
16.0
-1.0
15.5
17.0
0.0
17.4
18.0
Notes:
1.
Default levels are marked with white text on
black
2.
For the dBu value for input clipping level and
absolute max output level, a sine waveform is
assumed
3.
If numbers in dBV are required, dBV value is 2.2
dB lower than the dBu value.
Example: -10 dBu equals -12.2 dBV
D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011.
© 2010-2011 Cisco Systems, Inc. All rights reserved.
Introduction
Audio hardware information table
Signal type
Connector (codec)
Input impedance
Output impedance
Max input level when set to Min input level
-24.0
Max input level when set to Max input level
-23.0
Max output level when set to Min output level
-22.0
Max output level when set to Max output level
-21.0
Gain range
-20.0
Phantom power
-19.0
Phantom power resistor pin 1
-18.0
Phantom power resistor pin 2
-17.0
Max phantom power current (per mic)
-16.0
-15.0
-14.0
-13.0
* This specification is valid for Mic 1–8 inputs if Microphone Level setting is selected
-12.0
** This specification is valid for Line 1-8 inputs if Line Level setting is selected
-11.0
-10.0
-9.0
-8.0
-7.0
-6.0
-5.0
Volume control table
-4.0
-3.0
-2.0
-1.0
Ring tone volume*
0.0
* The ring tone volume, which is displayed on screen
when using the TRC5 remote control, goes from 0
to 20.
Connecting to the codec
Hardware Information
Mic 1–8 *
Balanced
XLR-F
8100 Ohm (pin 2–3)
–18dBu/275mVpp
–42dBu/35mVpp
48 Volt +/- 2%
6800 Ohm
6800 Ohm
14mA
Volume control
Audio gain value
0
0
1
-34.5 dB
70
0.0 dB
100
15.0 dB
20
Physical interface guide
The physical interface
The physical interface
Line in 1–8 **
Line out 5–6
Line in 1–4
Balanced
Balanced
Unbalanced
XLR-F
XLR-M
Female RCA/phono
10k Ohm (pin 2–3)
10 k Ohm
50 Ohm
24dBu/34.7Vpp
18dBu/17.4Vpp
0dBu/4.4Vpp
-6dBu/2.2Vpp
0dBu/4.4Vpp
24dBu/34.8Vpp
<–24dB (24 steps of 1dB) –>
Contact us
Line out 1–4
Unbalanced
Female RCA/phono
100 Ohm
-6dBu/2.2Vpp
18dBu/17.4Vpp
www.cisco.com