Cisco 3600 Series 사용자 설명서 - 페이지 5

{카테고리_이름} Cisco 3600 Series에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 3600 Series 7 페이지. Memory upgrade
Cisco 3600 Series에 대해서도 마찬가지입니다: 제품 개요 (10 페이지), 업그레이드 지침 (30 페이지), 소유자 매뉴얼 (17 페이지), 애플리케이션 노트 (41 페이지), 구성 매뉴얼 (36 페이지), 사용자 설명서 (25 페이지), 부록 (15 페이지), 매뉴얼 (5 페이지), 구성 참고 사항 (23 페이지), 구성 참고 사항 (18 페이지), 구성 참고 사항 (25 페이지)

페이지 인쇄
Cisco 3600 Series 사용자 설명서
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
2 Ethernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
1 ISDN Basic Rate interface(s)
32K bytes of non−volatile configuration memory.
8192K bytes of processor board System flash partition 1 (Read/Write)
8192K bytes of processor board System flash partition 2 (Read/Write)
−−− System Configuration Dialog −−−
Would you like to enter the initial configuration dialog? [yes/no]: n
Press RETURN to get started!
00:00:19: %LINK−3−UPDOWN: Interface BRI0/0, changed state to up
00:00:19: %LINK−3−UPDOWN: Interface Ethernet0/0, changed state to up
00:00:19: %LINK−3−UPDOWN: Interface Ethernet0/1, changed state to up
00:00:19: %LINK−3−UPDOWN: Interface Serial0/0, changed state to down
00:00:19: %LINK−3−UPDOWN: Interface Serial0/1, changed state to down
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface BRI0/0,
changed state to down
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/0,
changed state to up
Router>
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/1,
changed state to up
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface Serial0/0,
changed state to down
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface Serial0/1,
changed state to down
00:00:50: %SYS−5−RESTART: System restarted −−
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600−IS−M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
Copyright (c) 1986−1999 by cisco Systems, Inc.
Compiled Tue 07−Dec−99 02:21 by phanguye
00:00:50: %LINK−5−CHANGED: Interface BRI0/0,
changed state to administratively down
00:00:52: %LINK−5−CHANGED: Interface Ethernet0/0,
changed state to administratively down
00:00:52: %LINK−5−CHANGED: Interface Serial0/0,
changed state to administratively down
00:00:52: %LINK−5−CHANGED: Interface Ethernet0/1,
changed state to administratively down
00:00:52: %LINK−5−CHANGED: Interface Serial0/1,
changed state to administratively down
00:00:53: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/0,
changed state to down
00:00:53: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/1,
changed state to down
Router>
Router>enable
Router#copy startup−config running−config
Destination filename [running−config]?
1324 bytes copied in 2.35 secs (662 bytes/sec)
Router#
00:01:24: %LINEPROTO−5−UPDOWN: Line protocol on Interface BRI0/0:1,
changed state to down
00:01:24: %LINEPROTO−5−UPDOWN: Line protocol on Interface BRI0/0:2,
changed state to down
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#enable secret < password >