Argo XFETTO DCI HPL 설치 지침 매뉴얼 - 페이지 11

{카테고리_이름} Argo XFETTO DCI HPL에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Argo XFETTO DCI HPL 17 페이지. Installation instructions for air conditioner

페이지 인쇄

NOTE

Use DRY operation when you want to reduce the humidity

●

in the room.

●

Once the room temperature reaches the set level, the unit

repeats the cycle of turning on and off automatically.

During DRY operation, the fan speed is automatically set

●

(Remote control lamp

Dry operation is not possible if the indoor temperature is

●

10 °C or less.

FAN ONLY

If you want to make air circulate without any temperature

control, press

button until only the

appears on the display.

ADJUSTING THE FAN SPEED

AUTOMATIC

Simply set the FAN selector to the

microcomputer automatically controls the fan speed when

the AUTO mode is selected. When the air conditioner starts

operating, in heating or cooling, the fan speed varies (high

- medium - low - very low) according to the thermal load of

the room.

NOTE

The automatic speed is not available in FAN ONLY mode.

MANUAL

If you want to manually adjust speed just set the FAN selector

as desired.

High speed

Med. speed

NIGHT MODE / ENERGY SAVING

●

This mode enables you to save energy.

1. Set the

2. Press the

button.

3. The

mark appears on the display. Press the

button again to release the function.

What does the NIGHT mode mean?

When you select the NIGHT mode, the air conditioner will

modify automatically the set temperature after 60 minutes.

This enables you to save energy without sacrificing your

comfort.

OPERATING MODE

Heating

Cooling and Dehumidifying

NOTA

During the NIGHT mode the internal fan speed is

automatically lower and reduces the noise.

is ON) to prevent overcooling.

fan symbol

position.A

Low speed

selector to cool, dry or heat.

SET TEMPERATURE CHANGE

Lowered by 1 °C

Raised by 2 °C

COOLING AND DEHUMIDIFYING

Function selection

Room temperature

TIME

ELECTRICAL HEATING

This air conditioner is equipped with an electrical heater

that can operate in three ways:

- AUTO MODE - During AUTOMATIC OPERATION the

electrical heater switches on automatically depending on the

room temperature, the set temperature and the outdoor

temperature.

- BOOSTER - During HEATING OPERATION press the

button on the remote control in order to activate the

electrical heater that will switch on only depending on the

room temperature and the set temperature.

- FAN HEATER - During FAN OPERATION press FILTER

button on the remote control or press three times the

selector (blinking symbol

activate the electrical heater.

HIGH POWER MODE

You can select High Power only during cooling or heating

mode and not during automatic, dehumidifying (dry) and

fan mode. High Power mode allows to obtain the maximum

air conditioner's efficiency, either in cooling or heating mode

(heat pump). The user can choose to activate the High

Power mode, using the remote control unit, after having

selected cooling or heating mode and during this latter

mode, it can be used together with the electrical heater in

Booster way. Under these conditions the air conditioner

will reach its maximum thermal power and consequently

also the maximum electrical consumption and noise; it is

recommended to use the High Power mode only if the

outdoor temperature is very low and the selected room

temperature is difficult to be reached. On the contrary, if

you want to obtain the best performance in efficiency and

silentness, High Power mode is not recommended: let the

air conditioner run in normal condition (factory default

program).

To activate High Power mode it is necessary (after having

selected the cooling or heating mode) to press two times

the HIGH POWER button

acoustic signal confirmation); at the first pressure of the

button the symbol .....switches on, at the second pressure

this symbol disappears; at this point the operation lamp

(green lamp on the front panel of the air conditioner) begins

blinking slowly, indicating that High Power mode is activated;

it can be deactivated using the same procedure; therefore

the green lamp will stop blinking and it will be switched on

permanently.

HEATING

Function selection

Room temperature

TIME

on the display) in order to

(always waiting for the