Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 설치 참고 사항 - 페이지 8

{카테고리_이름} Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대한 설치 참고 사항을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 28 페이지. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대해서도 마찬가지입니다: 설치 참고 사항 (14 페이지), 솔루션 매뉴얼 (17 페이지), 설치 참고 사항 (46 페이지), 백서 (19 페이지), 설명 (1 페이지), 제품 게시판 (6 페이지), 공지 사항 (4 페이지), 데이터시트 (9 페이지), 데이터시트 (18 페이지), 백서 (18 페이지), 구성 매뉴얼 (8 페이지), 문제 해결 매뉴얼 (11 페이지), 설치 참고 사항 (18 페이지), 사용자 설명서 (17 페이지), 설치 참고 사항 (24 페이지), 매뉴얼 (19 페이지), 설치 참고 사항 (36 페이지)

페이지 인쇄
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 설치 참고 사항
Front Panel Description

Status LED

At startup, the CSM initializes various hardware components and communicates with the supervisor
engine. The Status LED indicates the supervisor engine operations and the initialization results. During
the normal initialization sequence, the status LED changes from off to red, orange, and green.
Note
For more information on the supervisor engine LEDs, refer to the Catalyst 6500 Series Switch Module
Installation Guide.
Table 1
Table 1
Color
Off
Red
Orange
Green
Green to orange
1. Enter the show environment temperature mod command to display the temperature of each of four sensors on the
2. CLI=command-line interface.
RJ-45 Connector
The RJ-45 connector, which is covered by a removable plate, is used to connect a management station
device or a test device. This connector is used by field engineers to perform testing and to obtain dump
information.
Catalyst 6500 Series Switch Content Switching Module Installation Note
8
describes the Status LED operation.
Content Switching Module Status LED
Description
The module is waiting for the supervisor engine to provide power.
•
The module is not online.
•
The module is not receiving power, which could be caused by the following:
•
Power is not available to the CSM.
–
Module temperature is over the limit
–
•
The module is released from reset by the supervisor engine and is booting.
•
If the boot code fails to run, the LED stays red after startup.
The module is initializing hardware or communicating with the supervisor
•
engine.
A fault occurred during the initialization sequence.
•
The module has failed to download its Field Programmable Gate Arrays
•
(FPGAs) at startup but continues with the remainder of the initialization
sequence and provides the module online status from the supervisor engine.
•
The module has not received module online status from the supervisor engine.
This problem could be caused by the supervisor engine detecting a failure in
an external loopback test that it issued to the CSM.
•
The module is operational; the supervisor engine has provided module online
status.
•
The module is disabled through the supervisor engine CLI
module disable mod command.
1
.
2
using the set
CSM
.
78-15751-03