Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 문제 해결 매뉴얼 - 페이지 5

{카테고리_이름} Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대한 문제 해결 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 11 페이지. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대해서도 마찬가지입니다: 설치 참고 사항 (14 페이지), 솔루션 매뉴얼 (17 페이지), 설치 참고 사항 (46 페이지), 백서 (19 페이지), 설명 (1 페이지), 제품 게시판 (6 페이지), 공지 사항 (4 페이지), 데이터시트 (9 페이지), 데이터시트 (18 페이지), 백서 (18 페이지), 구성 매뉴얼 (8 페이지), 설치 참고 사항 (28 페이지), 설치 참고 사항 (18 페이지), 사용자 설명서 (17 페이지), 설치 참고 사항 (24 페이지), 매뉴얼 (19 페이지), 설치 참고 사항 (36 페이지)

페이지 인쇄
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 문제 해결 매뉴얼
Appendix B
Troubleshooting
Determining the MWAM Cisco IOS Image Name
To determine the MWAM Cisco IOS image name, execute the following command at the Cisco
Supervisor 2 (see the
show cdp entry *
You can also execute the following command at the Supervisor to determine the MWAM Cisco IOS
image name:
session slot x processor [2-6]
Then issue the following command:
show version
You can also enter the following command from the privileged EXEC mode (also available through
show images at the processor complex):
show version

Verifying the MWAM Configuration

To determine the MWAM configuration, see the
page

DIMM Issue

The following shows a possible DIMM issue (CSCin29212) that may be solved by re-inserting the
DIMM memory:
*** Cache Error Exception***
Cache Err Reg = 0x14001f20
instruction reference, primary cache, , tag field error, error on internal request on
SysAD Bus,
PC = 0x800fb5d4, Cause Reg = 0x20008068, Status Reg = 0x400005
%MWAM-0-CORRECTABLE_ECC_ERR: A correctable ECC error has occurred,
A_BUS-L2_ERRORS: 0x0, A_BU
A-MEMIO-ERRORS: 0xFF, A_SCD_BUS_ERR_STATUS: 0x80DC0000
RRECTABLE_ECC_ERR: A correctable ECC error has occurred.

MWAM Performance Tuning

You can improve system performance (by 6 to 12 percent depending on the traffic type) by turning off
VLAN accounting:
Router# configure terminal
Router(config)# no vlan accounting
Router#
OL-7469-04
"Software Description" section on page 1-7
6-14.
for more details):
"Verifying the MWAM Configuration" section on
Multiprocessor WAN Application Module User Guide
MWAM Problem Solving
B-5