Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 설치 참고 사항 - 페이지 29

{카테고리_이름} Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대한 설치 참고 사항을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 36 페이지. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대해서도 마찬가지입니다: 설치 참고 사항 (14 페이지), 솔루션 매뉴얼 (17 페이지), 설치 참고 사항 (46 페이지), 백서 (19 페이지), 설명 (1 페이지), 제품 게시판 (6 페이지), 공지 사항 (4 페이지), 데이터시트 (9 페이지), 데이터시트 (18 페이지), 백서 (18 페이지), 구성 매뉴얼 (8 페이지), 설치 참고 사항 (28 페이지), 문제 해결 매뉴얼 (11 페이지), 설치 참고 사항 (18 페이지), 사용자 설명서 (17 페이지), 설치 참고 사항 (24 페이지), 매뉴얼 (19 페이지)

Depending on the orientation of the slots in the chassis (horizontal or vertical), perform one of the

Step 5

following two sets of substeps:

Horizontal slots

Vertical slots

Installing an Ethernet Module in the Chassis

Caution

To prevent ESD damage, handle modules by the carrier edges only and wear grounding wrist straps.

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into

Warning

beams or view directly with optical instruments. Statement 1051

To install a module in the chassis, perform these steps:

Verify that an ESD grounding strap is attached to your wrist and to proper ground.

Step 1

Verify that the captive installation screws are tightened on all of the modules installed in the chassis.

Step 2

This step assures that the EMI gaskets on all of the installed modules are fully compressed in order to

maximize the opening space for the Ethernet module.

Note

Catalyst 6500 Series Distributed Forwarding Card 4 for WS-X68xx, WS-X69xx, and Select WS-X67xx Modules Installation Note

OL-24918-02

Place your thumbs on the left and right ejector levers located on the left and right sides of the module

faceplate, and simultaneously rotate the levers outward to unseat the Ethernet module from the

chassis backplane connector.

Grasp the front edge of the Ethernet module and slide the module part of the way out of the slot.

Place your other hand under the Ethernet module to support the weight of the module. Do not touch

the module circuitry.

Place the removed Ethernet module on a properly grounded antistatic mat or antistatic foam.

Place your thumbs on the ejector levers located at the top and bottom of the Ethernet module, and

simultaneously rotate the levers outward to unseat the Ethernet module from the chassis backplane

connector.

Grasp the front edge of the Ethernet module and slide the module part of the way out of the slot.

Place your other hand under the Ethernet module to support the weight of the module. Do not touch

the module circuitry.

Place the removed Ethernet module on a properly grounded antistatic mat or antistatic foam.

If the captive installation screws are loose, the electromagnetic interference (EMI) gaskets on

the installed modules expand and push the modules toward the open slot, which reduces the

opening size and makes it difficult to reinstall the module.

Removing and Installing Ethernet Modules in the Chassis