Sony XC-ST30CE 사용자 설명서 - 페이지 7
{카테고리_이름} Sony XC-ST30CE에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Sony XC-ST30CE 31 페이지. Black-and-white video camera module
Sony XC-ST30CE에 대해서도 마찬가지입니다: 사양 (4 페이지), 제품 설명서 (2 페이지), 기술 매뉴얼 (30 페이지), 기술 매뉴얼 (31 페이지), 매뉴얼 (4 페이지)
페이지 인쇄
LOCATION OF PARTS AND OPERATION
XC-ST50/50CE
XC-ST30/30CE
2
(XC-ST50 model)
CCD
1
2 3
5
412-pin multi-connector
Pin No.
*
1: An input VD signal is required when the restart/reset mode is used.
2: A WEN output signal is valid only in the external trigger shutter mode.
*
Factory-setting mode of rear panel
Corresponding
No.
6
correction ON/OFF selector switch
7
Internal/external sync selector switch
8
Trigger polarity selector switch
9
75
termination selector switch
Selection DIP switch
0
1, 2, 3, 4: Selects the Shutter speed.
5: Selects the field and frame integration.
6, 7, 8: Selects the normal shutter, external trigger shutter, and restart/reset.
A
GAIN switch
VIDEO CAMERA MODULE
XC-ST50
6 7
4
A
B
=
9
External HD/VD
Internal HD/VD
synchronization
synchronization
1
GND
2
+12 V
+12 V
3
GND
4
VIDEO output
VIDEO output
5
GND
6
External HD input
Internal HD output
1
7
*
External VD input
Internal VD output
8
GND
9
–
2
2
10
*
WEN output
*
WEN output
11
TRIG input
TRIG input
12
GND
Switch
4 5
3
8
External VS
synchronization
GND
GND
+12 V
GND
GND
VIDEO output
GND
GND
–
VS
GND
GND
–
–
2
*
WEN output
TRIG input
GND
GND
Factory-setting
mode
OFF
EXT
+
ON
OFF
(All set to
the left.)
FIX
1 Lens mount section
A commercial C-mount lens as well as a
Sony standard lens can be used.
2 Camera mounting reference hole
These screw holes are positionned with
high precision related to CCD sensor.
3 Screw hole for tripod adaptor mounting
(VCT-ST70I)
4 12-pin multi-connector
DC IN/SYNC (DC power/sync signal input)
5 BNC connector
VIDEO OUT
6
correction
ON/OFF selector switch
7 Internal/external sync selector
switch
The camera operates with internal syn-
chronization when there is no external
sync input signal in the EXT position.
In this case, an HD/VD signal is not out-
put from the 12-pin multi-connector.
8 Trigger polarity selector switch
This switch can select the polarity (nega-
tive or positive) of a trigger pulse.
9 75
termination selector switch
0 Selection DIP switch
Switches 1 to 4:
Selects the shutter speed.
Switch 5: Selects the frame or field
Switches 6 to 8:
Selects the normal shutter,
external trigger shutter, and
restart/reset.
A GAIN switch
A: Outputs a fixed-level video signal ac-
cording to the brightness of a sub-
ject. (Variable range: 0 to 18 dB)
F: Fixed gain 0 dB
M: Variable gain (Manual)
M (during factory setting):
Adjusted so that all XC-ST50/50CEs
or XC-ST30/30CEs are the same in
sensitivity (set by Sony's standard
value) according to the deviation in
sensitivity of CCD.
Valid when multiple XC-ST50/50CEs
or XC-ST30/30CEs are used for an
identical subject.
B Volume control switch
This switch can be changed in the range
of 0 to 18 dB when the GAIN switch is set
to "M".
During factory setting, this switch is ad-
justed to the fixed sensitivity for a stan-
dard subject.
XC-ST50/50CE
XC-ST30/30CE
5