Sony BluetoothH MEX-BT5100 사용 설명서 - 페이지 16
{카테고리_이름} Sony BluetoothH MEX-BT5100에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Sony BluetoothH MEX-BT5100 45 페이지. Bluetooth audio system
Sony BluetoothH MEX-BT5100에 대해서도 마찬가지입니다: 설치/연결 (2 페이지), 설치/연결 (2 페이지), 빠른 매뉴얼 (2 페이지), 사양 (2 페이지), 빠른 매뉴얼 (2 페이지), 빠른 매뉴얼 (2 페이지)
페이지 인쇄
•
Tips
• Preset Dial also allows you to make
a
call by
pressing
a
number button twice after pressing
(CALL).
• On the "Dialed Calls," "Received Calls" and "Preset
Dial" menus, you can make
a
call by pressing
( CALL)
while the phone number is displayed.
Presetting the volume of ring tone
and talker's voice
You can preset the volume level of the ring tone
and talker's voice.
To adjust the ring tone:
Rotate the joystick while the phone is ringing.
"Ring Vol" appears and ring tone volume is set.
To adjust the talker's voice:
Rotate the joystick during a call. "Talk Vol"
appears and the talker's voice volume is set.
Sending DTMF (Dual Tone Multiple
Frequency) tones
You can send DTMF tones.
To send DTMF tones, use the joystick or press
the required number buttons (0 - 9,
*
or
#)
on
the card remote commander during a call.
Receiving calls
When receiving a call, ring tone is output from
your car speakers.
For details on the settings for receiving a call and
during a call, see "Setting a handsfree device" on
page 17.
1
When receiving a call, press @QJ,
( MENU)
or
(Bluetooth).
It1G~-
-
(B'U9tOO'h)
I,"~~~
The phone call starts.
To reject a call
Press
(OFF).
Tips
• If
you set "Auto Answer" to on, the phone call is
automatically started in the set time (page 17).
• If (
CALL)
is pressed during
a
call, the handsfree
function is deactivated, and the microphone and
speaker
of
the cellular phone are activated. In this
case, the Bluetooth connection may become
disconnected depending on the cellular phone.
Note
Even if the call is ended, the Bluetooth connection is
not canceled.
Using the Phonebook
Receiving phonebook data from a
cellular phone
1 Select "Phone Settings" from the Bluetooth
function menu.
2 Select "Receive PB."
"Waiting... " appears.
3 Send the phonebook data by operating the
cellular phone.
"Data Receiving..." appears while receiving
the phonebook data.
"Complete" appears when receiving is
complete.
Notes
• Before receiving phonebook data, disconnect any
cellular phone or audio device.
• To cancel the transfer
of
phonebook data, operate
the cellular phone. Transfer cannot be canceled from
this unit.
Storing the numbers from "Dialed
Calls" or "Received Calls"
1 Select "Dialed Calls" or "Received Calls"
from the CALL menu.
2 Select the phone number to store, then select
"Save."
The "Contact Name" display appears.
3 Input a name.
Up to 20 characters can be input.
4 Select "Save?"
~
"yes."
Note
Up to 50 phone numbers can be stored in the
Phonebook.
If
you try to register more than 50
numbers, "Memory Full" appears.
Deleting from the phonebook
1 Select "Phonebook"
~
"Contact List" from the
CALL menu.
2 Select the name to delete.
3 Select "Delete Contact"
~
"yes."
To clear all phonebook data, select "Delete All"
in step 1. After clearing, confirm that all
phonebook data has been cleared properly.
16
Ending calls
1
Press
(OFF).
When the call ends, talk time appears for a
few seconds.
Changing a name in the phonebook
1 Select "Phonebook"
~
"Contact List" from the
CALL menu.
2 Select the name to change.
3 Select "Edit Name," then input a new name.