Sony RDP-X200iPN 운영 지침 - 페이지 2
{카테고리_이름} Sony RDP-X200iPN에 대한 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Sony RDP-X200iPN 2 페이지. Personal audio
system
Sony RDP-X200iPN에 대해서도 마찬가지입니다: 운영 지침 (2 페이지), 운영 지침 (2 페이지)
페이지 인쇄
Startup Guide
iPod indicator
Power indicator
Bluetooth indicator
MEGA BASS indicator
Remote sensor
Docking Tray
VOLUME + (VOL + on the remote control) and buttons have a tactile dot.
Operations
To turn the unit on/off
Press (On/Standby).
The power indicator lights up when the unit is turned on.
How to handle an iPod
To set an iPod
Adjusting the volume
Press VOLUME +/− (VOL +/− on the remote).
Tip
The power indicator flashes three times in green when
the sound is set to either maximum or minimum
volume.
Operating an iPod on the
Dock
1
Set the iPod on the Dock Connector.
The Dock Connector can be tilted slightly.
For details, see "How to handle an iPod. "
To remove an iPod
2
Press .
3
Press iPod to activate the function for iPod.
The iPod indicator lights up.
4
Press .
The iPod begins to play back.
If the iPod does not start playing back, operate directly
on the iPod.
You can operate the connected iPod via this unit or the
iPod itself.
To
Pause playback
Notes
An iPod in a case or cover can be set in this unit.
However, if the case or cover interferes with the
Go to the next track
connection, remove the case or cover before setting the
iPod on the Dock Connector.
Go back to the previous track
When placing or removing the iPod, hold it at the same
angle as the Dock Connector on the unit. Do not pull
Locate a point while listening to
the iPod forward too far.
the sound
When placing or removing the iPod, hold the unit
securely.
Do not twist or bend the iPod, as this may result in
connector damage.
Remove the iPod when transporting it; otherwise, a
malfunction may result.
Go back to the previous menu
Select a menu item or a track
for playback
5
To
Press
Execute the selected menu item
ENTER on the remote
or begin playback
* During playback, this operation returns you to the beginning of
the current track. To go back to the previous track, press twice.
Audio-in
Notes
indicator
If a pop-up message appears on the display of the iPod
touch, iPhone or iPad, see "About App. "
Some operations may differ or may not be available on
some models of iPod.
If the battery of the iPod is extremely low, charge it for a
while before operation.
Sony cannot accept responsibility in the event that data
recorded to an iPod is lost or damaged when using the
iPod connected to this unit.
For details of environmental conditions for operating an
iPod, check the website of Apple Inc.
MENU, (up), (down), and ENTER button on the
main unit and/or on the supplied remote control will
only work with the Apple devices (iPhone/iPad/iPod
touch) installed up to iOS 6. It will not work with iOS 7
Notes
or later. In such case, please operate on the screen of
The operation and display may differ depending on the
Apple devices directly.
model of iPod and/or software version. For details, refer
To remove the iPod
to the user's guide of the iPod.
Pairing mode is canceled after about 5 minutes. If
For details, see "How to handle an iPod. "
pairing mode is canceled halfway, start over from step 3.
To charge an iPod
If pairing is not complete, start over from step 3.
To pair with another iPod, repeat steps 1 to 5.
You can use the unit as a battery charger for an iPod.
In step 3, if a double-beep sound is not heard or the
Charging begins when the iPod is connected to the unit.
Supporter
Bluetooth indicator does not flash quickly, press and
The charging status appears in the display on the iPod. For
hold BLUETOOTH (
details, refer to the user's guide of the iPod.
If you turn off the unit or the iPod before the Bluetooth
connection is complete, pairing information will not be
memorized, and pairing will not be completed.
Dock Connector
Operating by wireless music
Notes on pairing with a Bluetooth device other than
streaming
iPod
When pairing with a Bluetooth device other than iPod,
By using the Bluetooth connection, you can listen to the
after step 3, pass code input may be required in your
sound from an iPod or other Bluetooth device with the
Bluetooth device. In this case, input "0000. "
unit wirelessly.
The operation and display may differ depending on the
Bluetooth device and/or software version. For details,
refer to the user's guide of the Bluetooth device.
To listen to sound
Keep the iPod and the unit within 10 meters of each other
for this operation.
Check the following before operating the unit.
The Bluetooth function of the iPod is on.
Pairing of the unit and the iPod is complete. If pairing is
not completed, perform pairing again. (See "To pair with
an iPod. " )
Pairing
1
What is pairing?
2
Bluetooth devices need to be "paired" with each other
beforehand.
Once Bluetooth devices are paired, there is no need for
pairing again, unless pairing information is deleted.
Bluetooth indicator
3
Status
Bluetooth indicator
(blue)
Bluetooth off
Off
Tips
Bluetooth on but not
Flashes slowly
connected
If the last connected iPod does not reconnect
automatically, press BLUETOOTH (
Pairing mode
Flashes quickly
it still does not reconnect, select the model name of this
Connected or communicating
Lights up
unit from the iPod. (Perform steps 4 to 5 in "To pair
with an iPod. " )
To pair with an iPod
To connect an alternative iPod, which has previously
Keep the iPod and the unit within 1 meter of each other for
been paired with this unit, press BLUETOOTH (
this operation.
remote) to disconnect the currently connected iPod.
1
Press .
Then select the model name of the unit from the
2
alternative iPod you want to connect.
Press BLUETOOTH ( on the remote) to turn on
the Bluetooth function when the Bluetooth
You can charge the iPod on the dock while listening to
music via Bluetooth connection.
indicator is off.
If the volume level is low, adjust the volume of the unit
The Bluetooth indicator flashes slowly.
first. If the volume is still too low, adjust the volume of
3
Press and hold BLUETOOTH ( on the remote).
the Bluetooth device.
When pairing starts, a double-beep sound will be heard
To finish listening
and the Bluetooth indicator will flash quickly.
Terminate the Bluetooth connection by any of the
Pairing mode of the unit is activated.
following operations.
Turn off the unit.
Turn off the iPod.
Press BLUETOOTH (
IN.
Operate the iPod to terminate the connection. For
details, refer to the user's guide of the iPod.
4
To clear the list of models already-
Perform the pairing procedure on the iPod to
detect the unit. Select "Settings Bluetooth" and
paired and memorized in the unit
turn on the Bluetooth function.
1
The Bluetooth indicator lights up.
2
Example: iPhone 5
Press
3
To resume play, press
again.
(forward) on the
Notes
remote
You can perform step 3 to clear the list even during
Bluetooth connection.
(backward)* on
This operation cannot be performed when the unit is
the remote
pairing.
(forward) or
To pair with this unit again, delete the model name of
(backward) on
this unit from the iPod and perform pairing again. (See
the remote while
"To pair with an iPod. " )
playing and hold until
you find the desired
point.
MENU on the remote
A list of detected devices appears on the display.
(up)/ (down) on
The unit is displayed as "RDP-X200iPN. "
the remote
If "RDP-X200iPN" is not displayed, repeat from step 3.
Select "RDP-X200iPN" on the display of the iPod
Connecting optional
while the Bluetooth indicator flashes quickly.
components
When "Connected" appears on the display of the iPod,
pairing and connection are complete.
You can enjoy the sound from an optional component,
Example: iPhone 5
such as a portable digital music player, through the
speakers of this unit. Be sure to turn off the power of each
component before making any connections.
1
Firmly connect the line output jack of the
portable digital music player (or other
component) to the AUDIO IN jack on the back of
the unit, using a suitable audio connecting cable
(not supplied).
2
Press to turn on the unit.
3
Press AUDIO IN to activate the Audio-in
function.
The Audio-in indicator lights up.
4
Turn the connected component on.
5
Play the connected component.
The sound from the connected component is output
from the speakers of this unit.
Notes
The necessary type of audio connecting cable depends
on the optional component. Be sure to use the correct
type of cable.
If the volume level is low, adjust the volume of the unit
first. If the volume is still too low, adjust the volume of
the connected component.
on the remote) again.
Other useful functions
Reinforcing the bass sound
Press MEGA BASS.
The MEGA BASS indicator lights up. To return to normal
sound, press the button again.
About App
A dedicated Dock App for iPod touch/iPhone/iPad
available at Apple App Store.
Search for "D-Sappli" and download the free App to find
out more about the functions.
Features
D-Sappli includes various timer functions: Alarm, Music
Play Timer and Sleep Timer.
You can set up to 10 alarms, using songs in iPod or
Press .
Preset Sound in D-Sappli for the alarm sound.
Press BLUETOOTH ( on the remote) to turn on
Music Play Timer allows you to play/pause desired
music at a desired time. Sleep Timer allows you to
the Bluetooth function.
specify a time at which to stop music playback. Alarm,
The last connected iPod will be reconnected
Music Play Timer and Sleep Timer work in combination
automatically when the Bluetooth function is turned
with the power supply of the unit.
Alarm, Music Play Timer and Sleep Timer are available
on.
only when D-Sappli is activated.
Select your desired music, video, game, etc., to
D-Sappli also includes a clock display enlarge feature.
play on the iPod. For details, refer to the user's
Notes
guide of the iPod.
If the App to link with this unit is not downloaded to the
iPod touch/iPhone/iPad, a pop-up message prompting
you to download D-Sappli may appear repeatedly.
on the remote). If
Deactivate the App's link function to stop the pop-up
message.
To deactivate the App's link function: Connect the AC
adaptor, and then press / to turn off the unit. Remove
the iPod touch/iPhone/iPad from the Dock Connector.
While holding down , also press and hold / on the
on the
unit for at least 2 seconds. (The power indicator flashes
twice when deactivated.)
To re-activate the App's link function, repeat the above
steps. (The power indicator flashes once when activated.)
on the remote), iPod, or AUDIO
Press .
Press BLUETOOTH ( on the remote) to turn on
the Bluetooth function.
Press and hold BLUETOOTH and VOLUME − on
the unit at the same time.
The MEGA BASS indicator flashes.