Digitone Call Blocker 소유자 매뉴얼 - 페이지 3

{카테고리_이름} Digitone Call Blocker에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Digitone Call Blocker 13 페이지. Automatically blocks and routes screened calls with caller id
Digitone Call Blocker에 대해서도 마찬가지입니다: 코드 목록 (2 페이지)

페이지 인쇄

How Digitone's Call Blocker Operates

When calls come in, all calls displaying a phone number will ring through to the phones

throughout your home/office like normal and to the TEL phone port on the back of the Call Blocker. Calls

like Anonymous, Out Of Area, Private and Unknown displaying no phone number will be answered by

the Call Blocker and hung-up on unless program Code 72 is enabled to allow these call types to ring in.

If you are running a business and want to hear from Anonymous, Out Of Area, Private and Unknown

callers, you can enable Business Mode Code 31 to allow all callers to ring through except those

numbers you want to block. Blocked callers will be immediately answered and after one ring get hung-

up on. The blocked caller only hears one ring in their phone and then silence. If you miss your Invited

caller, your combo phone-answer machine attached to the TEL phone port or phone company voice mail

will take a message for you. If your caller hangs-up during any part of the call, so will Call Blocker to

await another call. VIP callers can ring through at any time regardless of After Hours Mode or Invited

caller settings. Invited callers can only ring through normally when After Hours Mode is not enabled.

Types of Incoming Calls

Default settings are ALL calls with numbers ring through. All calls without numbers are

answered and hungup on. The Blocked caller hears only one ring and then silence. The Call Blocker

will allow all phones connected to the line to ring as well, then after seven rings the Call Blocker will

hang-up the call, assuming the answer machine doesn't answer the call first.

Invited Callers - 30 numbers or area codes The factory setting is: Global Invite of any call with

a standard number displayed. Invited callers cannot ring through during the After Hours Mode. If you

want specific callers to ring through at that time they must be added to the VIP list.

Invited Caller List

Limits include either unlimited numbers with Code 96 # * (factory setting) or added individually.

VIP Callers - 30 numbers These callers will be allowed to ring through at all times and are stored in a

separate VIP list from the Invited callers. VIP callers can ring through even when the After Hours Mode

is used to route calls away from the phone in the TEL phone port. This caller list should be used for your

immediate family or associates who will need full access to you and your phone or for emergencies.

Blocked Callers - 80 numbers or area codes Callers on your Blocked list cannot ring your phone in

the TEL phone port and cannot leave a message. Blocked numbers are numbers that you add and will be

answered immediately, followed by a hang-up after 8 seconds. The Red light will flash quickly when a call

is being blocked and a busy signal will be heard in the handset of the phone in the TEL phone port.

Invited Callers within a Blocked Area Code - 10 numbers Up to 10 separate numbers within an

area code can be allowed to ring through when the entire area code is already blocked. Example: phone

number 800-555-1212 is invited to ring through but the rest of the area code 800 is blocked.

OPX Type Calls - OPX calls display as: Anonymous, Out of Area, Private and Unknown or "X" calls that

do not have a minimum 7 digit number displayed, or have characters in the number like # or *, or have

been "Spoofed" to look like a real number. The factory setting is to hang-up on these type of calls.

™

First Ring Suppression

– Caller ID Pass Thru Mode (Code 70)

When a call comes in, the phone company's Caller ID information will display on all phones connected

to the telephone line but the Call Blocker will suppress the first ring to the TEL phone port to

prevent it from ringing and receiving Caller ID. If the caller is an Invited caller then the Caller ID

information will display on the next ring to the phones connected to the TEL phone port thereafter. This

stops unwanted Caller ID information from being received by the phones connected to the Call Blocker's

TEL phone port. If you want to hear the first ring, enter programming: press and hold the Program

Button for 3 seconds until you see "Program Mode", then "Pick Up Phone", when the prompt for "Enter

Code" displays enter code 71. This code will allow all rings and all Caller ID information to be received

by phones connected to the TEL phone port. To return to the (default) First Ring Suppression mode,

enter programming: when the prompt for "Enter Code" displays enter code 70, display shows function.