Digitone DCB Plus 소유자 매뉴얼 - 페이지 10

{카테고리_이름} Digitone DCB Plus에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Digitone DCB Plus 16 페이지. Automatically blocks and routes screened calls with caller id

페이지 인쇄

Step 3) Saturday & Sunday - Enable

If you want the same time interval to work during Saturday and Sunday, when the prompt for "Enter

Code" displays, enter 86, display shows function.

To disable this feature, when the prompt for "Enter

Code" displays, enter 87, display shows function.

Step 4) After Hours Mode ON or OFF – (Code 80/81)

To enable After Hours Mode, enter programming: when the prompt for "Enter Code" displays, enter 81,

display shows function. To turn this feature Off, when the prompt for "Enter Code" displays enter 80,

display shows function. Note: To enable After Hours Mode you must first enter Start and End times

(above) and enable day periods (M-S).

DTMF Caller ID Format (Code 17)

Some countries (not USA) use DTMF for Caller ID service and you can switch to this mode from the

default of FSK. To enable the DTMF mode, press and hold the Program Button for 3 seconds until you

see "Program Mode", then "Pick Up Phone", when the prompt for "Enter Code" displays enter 17, display

shows function. To return to the default FSK mode when the prompt for "Enter Code" displays, enter 16.

LED Flashing (Code 28)

The DCB Plus red LED comes from the factory set to flash for new calls, ringing, blocked calls and

programming prompts. If you do not want to see the LED flashing at all, you can disable it with Code 29.

Press and hold the Program Button for 3 seconds until you see "Program Mode", then "Pick Up Phone",

when the prompt for "Enter Code" displays, enter 29. To re-enable the LED flashing, enter 28.

Anonymous, Out of Area, Private and Unknown (Code 72)

If you want to have an answer machine or your voice mail take these types of calls and not ring your

phone connected to the DCB Plus you can program in Code 72 (OPX override). Note that Code 72 allows

the OPX calls through to the Line only, not the TEL phone port.

To enable OPX Override, enter

programming: press and hold the Program Button for 3 seconds until you see "Program Mode", then

"Pick Up Phone", when the prompt for "Enter Code" displays enter 72, display shows function. If you

want to restore Blocking of OPX calls later, enter programming: press and hold the Program Button for 3

seconds until you see "Program Mode", then "Pick Up Phone", when the prompt for "Enter Code"

displays, enter 73, display shows function.

"Private" Call Pass Thru (Code 74)

Using Code 74 can allow "Private" type calls with No Number displayed to ring through to the TEL phone

port while still blocking Out of Area and stored numbered calls. To enable Private Call Pass Thru, enter

programming: then enter 74, when "Enter Code" displays. To turn this feature Off, when the prompt for

"Enter Code" displays enter 75, display shows function.

"Out of Area" Call Pass Thru (Code 76)

Using Code 76 can allow "Out of Area" type calls with No Number displayed to ring through to the TEL

phone port while still blocking Private and stored number calls. To enable Out of Area Call Pass Thru,

enter programming: then enter 76, when "Enter Code" displays. To turn this feature Off, when the

prompt for "Enter Code" displays enter 77, display shows function.

PBX Extension Pass Thru (Code 78)

Using Code 78 can allow a PBX system that uses 1 to 6 digit extension numbers to pass through the DCB

Plus without being hungup on as a OPX type call. Code 78 overrides this function and extension ringing

is possible while still blocking Out of Area, Private and Anonymous calls. To enable PBX Pass Thru, enter

programming: then enter 78, when "Enter Code" displays. To turn this feature Off, when the prompt for

"Enter Code" displays enter 73, display shows function.