Digitrax LocoMotion DN163K0b 매뉴얼 - 페이지 5

{카테고리_이름} Digitrax LocoMotion DN163K0b에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Digitrax LocoMotion DN163K0b 8 페이지. N scale mobile decoder

페이지 인쇄

Mid point Voltage (CV06) and Max Voltage (CV05). These values are set at

000/x00 at the factory. All have a range of values from 000/x00 to 255/xFF. We

recommend the following CV values as a starting point for experimenting with

speed tables in your locomotive.

Loco Type

Switcher

Concentrated low speed. Limited top

speed

Road Switcher

Prototypical top speed w/evenly

distributed curve from 0 to top speed

Mainline Loco

Quick increase to cruising speed then

levels off to prototypical top speed.

S S w w i i t t c c h h i i n n g g S S p p e e e e d d , , N N o o r r m m a a l l D D i i r r e e c c t t i i o o n n o o f f T T r r a a v v e e l l & & S S c c a a l l e e a a b b l l e e S S p p e e e e d d

S S t t a a b b i i l l i i z z a a t t i i o o n n ( ( B B a a c c k k E E M M F F ) ) F F e e a a t t u u r r e e s s

Switching speed is controlled by CV54. The default value is 000/x00 for OFF.

To turn on switching speed, program CV54 to a value of 001/x01. This allows

you to use F6 to activate/deactivate switching yard speed.

Normal Direction of Travel is controlled by CV29 bit 0.

The intensity of Scaleable Speed Stabilization (Back EMF) is controlled by

CV57. The default value for this feature is 006/x06 which is suitable for most

locos. You can adjust this value in the range of 000/x00 for OFF to 015/x0F for

the maximum effect. Consult your Decoder Manual for info about CVs 55 &

56 and their effects on scaleable speed stabilization.

F F u u n n c c t t i i o o n n O O u u t t p p u u t t s s o o n n t t h h e e D D N N 1 1 6 6 3 3 K K 0 0 b b

The DN163K0b is set up at the factory to control six functions. The unit is pre-

wired with one golden-white LED set up as Function 0 (F0F-forward and F0R-

reverse) for directional lighting shown in Figure 5 (next page) as F0F/F0F+ for

the front light. The front light will go off when the locomotive is running in

reverse. Functions F1, F2, F3 and F4 are available on the decoder and can be

used by soldering wires from the pads indicated to the lights (or other functions)

2 2 4 4 4 4 3 3 T T r r a a n n s s m m i i t t t t e e r r R R D D

P P a a n n a a m m a a C C i i t t y y , , F F l l 3 3 2 2 4 4 0 0 4 4

w w w w w w . . d d i i g g i i t t r r a a x x . . c c o o m m

V Start

CV02

002/x02

8 8 5 5 0 0 - - 8 8 7 7 2 2 - - 9 9 8 8 9 9 0 0

T T

8 8 5 5 0 0 - - 8 8 7 7 2 2 - - 9 9 5 5 5 5 7 7

F F

s s a a l l e e s s @ @ d d i i g g i i t t r r a a x x . . c c o o m m

E E

V Mid

V Max

CV06

CV05

038/x26

064/x50

048/x30

098/x62

128/x80

154/x9A