Fimer PVS-60-TL 빠른 설치 매뉴얼 - 페이지 2

{카테고리_이름} Fimer PVS-60-TL에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fimer PVS-60-TL 8 페이지. Solar inverter

페이지 인쇄

1. Labels and Symbols

The labels on the inverter show the conformity marking, main technical

data and identification of the equipment and manufacturer.

The below labels are intended as an example only; in fact, other models

of inverter are available

Regulatory Label

Identification label

WLAN embedded board Serial Number

WLAN embedded board Part Number

SN WLAN: SSSSSSSSSS

PN WLAN: PPP.PPPPP.PP

MAC address:

To be used to obtain the SSID of the wireless access

Mac Address:

point created by the inverter: ABB-XX-XX-XX-XX-

XX:XX:XX:XX:XX:XX

XX-XX (where "X" is a hex digit of the MAC address).

Remove and apply on the Quick installation guide

To be used to obtain the "Host Name": http://ABB-

SN WLAN: SSSSSSSSSS

XX-XX-XX-XX-XX-XX.local (where "X" is a hex digit

SN Inverter: SSSSSSSSSS

MAC: XX:XX:XX:XX:XX:XX

of the MAC address).

PK: KKKK-KKKK-KKKK-KKKK

MAC address it's the only required information to

Wireless

Inverter Serial Number

Identification Label

Product Key:

To be used as wireless access point password, or to

be used to access to the Web UI as username and

password in case of lost credentials, and to commission

inverter using ABB Installer for Solar Inverters.

ATTENTION –

The labels placed on the equipment absolutely

MUST NOT be removed, damaged, dirtied, hidden, etc.

In the manual and/or in some cases on the equipment, the danger

or caution areas are indicated with signs, labels, symbols, icons.

Always refer to instruction manual

General warning - Important safety information

Dangerous voltage

Hot surfaces

Protection rating of equipment

Temperature range

Without insulation transformer

Direct and alternating current, respectively

Positive and negative pole of the input voltage (DC)

Obligation to use protective clothing and/or personal

protective equipment

Point of connection of the protective ground

Risk of electric shock.The discharge time (quantified in the

figure by the number XX) of the stored energy after de-

energizing of the Inverter from both DC side and AC side.

Inverter Model

Inverter Part Number

Inverter Serial Number consisting of:

YY = Year of manufacture

WW = Week of manufacture

SSSSSS = sequential number

Week/Year of manufacture

Manufacturer

2. Installation site and position

• Consult technical data to confirm the environmental specifications will

be met.

• Installation of the unit in a location exposed to direct sunlight is acceptable.

Except for the version equipped with a display.

• Do not install in closed spaces where air does not freely circulate.

• Always ensure that the flow of air around the inverter is not blocked, so as

to prevent overheating.

• Do not install near flammable substances (minimum distance: 3 m).

• Do not install near on wooden walls or near flammable surfaces.

• Do not install in rooms where the people live or where the prolonged

presence of people or animals is expected.

• Installation of these models can be carried out vertically or horizontally

with a maximum inclination as indicated in the figures.

• Hardware and software maintenance on device entails opening the front

door. Check that the correct installation safety distances are observed in

order to allow routine check and maintenance operations.

• Install on a wall or strong structure suitable to bear the weight.

• If possible, install at eye-level so that the status LEDS can be seen easily.

• Install at a height which takes into consideration the weight of the

appliance and in a position which is suitable for servicing, unless suitable

means are provided to carry out the operation.

• Final installation of the device must not compromise access to any

disconnection devices that may be located externally.

• Respect the minimum distances from objects around the inverter that

could prevent the inverter installation and restrict or block the air flow.

• Provide sufficient working space in front of the inverter that allows to

make connections on the wiring box.

• In case of multiple installation position the inverters side by side keeping

the minimum distances (measured from the outer edge of the inverter)

for each inverter. If the space available does not allow this arrangement,

position the inverters in a staggered arrangement as shown in the figure

so that heat dissipation is not affected by other inverters below.

• The vertical installation in also permitted on a structure which must be

composed of a support for the attachment of the bracket and one for the

support of the rear pins.

• The vertical installation of two inverters positioned back to back in also

permitted on a structure which must be composed of 2 supports for the

attachment of the brackets.

• The inverter operates normally up to 2000 meters; between 2000 and

4000 meters the inverter works in derating (to verify curve derating),

above 4000 meters the installations are forbidden.

• Never open the inverter in the case of rain, snow or a level of humidity

>95%.

PVS-60

50 cm

30 cm

PVS-60

50 cm

5 ̊ max

ATTENTION –

Do not block access to the external AC and DC

disconnect switches.

ATTENTION –

Please refer to the warranty terms and conditions

and avoid voiding the warranty with improper installation.

PVS-60

OPE

LOC

OPE

20 cm

LOC

OPE

LOC

PVS-60