Cisco Linksys WAG110 사용자 설명서 - 페이지 17

{카테고리_이름} Cisco Linksys WAG110에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco Linksys WAG110 33 페이지. Wireless adsl2+ gateway

페이지 인쇄

Appendix D

Appendix D:

Regulatory Information

United States of America

The following information applies if you use the product

within the United States of America.

FCC Statement

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

This product has been tested and complies with the

specifications for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in

a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not

installed and used according to the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception,

which is found by turning the equipment off and on, the

user is encouraged to try to correct the interference by

one or more of the following measures:

Reorient or relocate the receiving antenna

•

Increase the separation between the equipment or

•

devices

Connect the equipment to an outlet other than the

•

receiver's

Consult a dealer or an experienced radio/TV technician

•

for assistance

FCC Caution: Any changes or modifications not expressly

approved by the party responsible for compliance could

void the user's authority to operate this equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure

limits set forth for an uncontrolled environment. This

equipment should be installed and operated with

minimum distance 20cm between the radiator and your

body.

This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter. IEEE

802.11b or 802.11g operation of this product in the USA is

firmware-limited to channels 1 through 11.

Wireless ADSL2+ Gateway

Regulatory Information

FCC Part 68 Statement

This equipment complies with Part 68 of the FCC Rules. A

label is attached to the equipment that contains, among

other information, its FCC registration number and ringer

equivalence number. If requested, this information must

be provided to the telephone company.

This equipment uses the following USOC Jack: RJ-11.

An FCC compliant telephone cord and modular plug

is provided with this equipment. This equipment is

designed to be connected to the telephone network or

premises wiring using a compatible modular jack, which

is FCC Part 68 compliant. Connection to the telephone

network should be made by using the standard modular

telephone jack.

The REN is useful to determine the quantity of devices

that may be connected to the telephone line and still have

all of those devices ring when your telephone number is

called. In most, but not all areas, the sum of RENs should

not exceed 5. To be certain of the number of devices that

may be connected to the line, as determined by the total

RENs, contact the telephone company to determine the

maximum REN for the calling area.

If this equipment causes harm to the telephone network,

the telephone company may discontinue your service

temporarily. If advance notice is not practical, the

telephone company will notify the customer as soon as

possible. Also, you will be advised of your right to file a

complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its

facilities, equipment, operations, or procedures that could

affect the operation of the equipment. If this happens, the

telephone company will provide advance notice in order

for you to make the necessary modifications in order to

maintain uninterrupted service.

In the event this equipment should fail to operate properly,

disconnect the unit from the telephone line. Try using

another FCC approved device in the same telephone

jack. If the trouble persists, call the telephone company

repair service bureau. If the trouble does not persist and

appears to be with this unit, disconnect the unit from the

telephone line and discontinue use of the unit until it is

repaired. Please note that the telephone company may ask

that you disconnect the equipment from the telephone

network until the problem has been corrected or until

you are sure that the equipment is not malfunctioning.

The user must use the accessories and cables supplied by

the manufacturer to get optimum performance from the

product.

No repairs may be done by the customer. If trouble is

experienced with this equipment, please contact your

authorized support provider for repair and warranty

information. If the trouble is causing harm to the

telephone network, the telephone company may request