Digium Switchvox AA355 빠른 시작 매뉴얼

{카테고리_이름} Digium Switchvox AA355에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Digium Switchvox AA355 2 페이지.

페이지 인쇄

Digium

AA355 Appliance

Quick Start Guide

You've purchased a PBX. Now what?

The AA355 was created with ease of use in mind.

You will find that it is very easy to install and set up the

AA355. There are just a few simple steps needed to install

the appliance. To install and prepare your AA355 for use,

follow the steps in this document.

Changes or modification to the unit not expressly approved by

Digium could void the user's authority to operate the equipment.

613-00008-A

Thank you for your purchase of the

Digium

AA355 Appliance. This document

is your Quick Start Guide for the initial setup

and installation of the AA355. For questions

about setting up your Digium software product,

please refer to the reverse side of this sheet.

In the box you will find:

The Digium AA355

AC power cable

(Quantity: 2)

Bracket screws

(4)

Sliding rack rails

(2)

Installation media and literature

Digium's Support Center, including Technical

Support contacts, Documentation and

Knowledge Base, may be visited online at

www.digium.com/en/supportcenter

Digium's Policies, including Warranty and

Return procedures, may be viewed online at

www.digium.com/en/company/policies.php

On this product,

NOTICE:

the power cables serve

as the disconnect device.

In order to service the

unit, the power cables

must be disconnected.

Hardware Installation

1. Remove the AA355 from its box.

2. Place the AA355 in a location that will be secure

and where the AA355 will be able to operate

efficiently. Install the AA355 into a standard com-

puter rack or cabinet. Please refer to the AA355

Mounting Instructions section for more information.

3. Connect your AA355 to your data network.

Connect an Ethernet cable from your computer

network to the left-hand Ethernet socket on the rear

of the AA355.

4. Plug in the cables connecting your AA355 to the

PSTN and to one or more telephones. The

connections will be dependent on the Digium

telephony interface cards included with your AA355.

5. Connect the AA355 power cables to the power

ports on the rear of the AA355 unit and then

connect the power cables to wall outlets. The

AA355 should automatically power itself to the on

position. If it did not, open the doors on the front of

the unit and depress the unit's power button until

the power LED illuminates.

6. The hardware installation of your unit is now

complete. Please refer to the Software Quick Start

Guide on the rear of this sheet.

Mounting Instructions

The Digium

AA355 must be mounted into a standard

19" computer cabinet or rack and requires 3U of vertical

space. The rail kit for the AA355 is for round hole racks.

To mount the AA355, follow these instructions.

1. Begin installation by securing the sliding rails to the

AA355 chassis. To do this, first extend each three-

piece rail kit until it locks. Depress the spring safety

lock to release the inner rail and then remove the

inner-rail from each of the two rail assemblies.

2. Attach the inner rails to the AA355 chassis using the

screws provided in the AA355 rail kit.

3. Locate 3U of available space in your server rack.

The outer rails of the rail kit use sliding brackets to

extend to the proper depth of your rack. Loosen the

bolts and slide the brackets to the depth of

your rack.

4. Attach the brackets and outer rails to your rack.

Take care to align each of the outer-rails on the

same vertical space.

5. Tighten the bolts on the outer-rails of the rail kit.

6. Slide the AA355 into the front of the rack and align

the inner-rails into the outer-rails. Make certain to

slide the AA355 completely into the rack until the

rails lock into position.

Telephony Card Installation

The Digium

AA355 is designed to be used with up

to three Digium telephony interface cards from

the following list:

Digium TDM410

Digium TE122

Digium TDM800

Digium TE205/TE207

Digium TDM2400

Digium TE405/TE407

Digium B410P

To install Digium telephony cards, follow

the steps below.

1. Power down the AA355 (if it is running) by navigating

the front panel LCD and selecting "Shutdown PBX".

Once the shutdown process has finished, unplug

the unit from its power source.

2. Make sure that you are grounded by attaching a

static strap to your wrist.

3. Remove the AA355 from its rack-mounted location.

4. Remove the AA355 case lid screws and then the

case lid.

5. Remove the PCI blank cover from the rear panel

corresponding to the hardware card slot you will

use. Note that only three slots are available

for customer use.

6. Insert the Digium card you have selected into the PCI

slot and secure it with a screw, noting which ports, if

any, are FXO (red) and which ports are FXS (green).

7. If your card has any FXS modules, you will also

need to connect a power cable from the AA355

power supply to the rear of the telephony card. In-

sert a 4-pin, 12 volt connector into the white plastic

connector on the rear of the card.

8. Replace the lid of the AA355 and return it to

its rack location.

9. Plug all outside phone lines to the FXO (red) ports

and connect all phones to the FXS (green) ports.

For more information on the Digium card(s) you

have selected for your AA355, please refer to the

card manual available at www.digium.com