Epson Stylus color 600 매뉴얼 - 페이지 18

{카테고리_이름} Epson Stylus color 600에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson Stylus color 600 19 페이지. Epson stylus color 600: quick setup
Epson Stylus color 600에 대해서도 마찬가지입니다: 사용자 설명서 (34 페이지), 사용자 설명서 (38 페이지), 사용자 설명서 (35 페이지), 사양 (1 페이지), 제품 정보 시트 (4 페이지), 빠른 설정 매뉴얼 (17 페이지)

페이지 인쇄

EPSON Stylus COLOR 600

Caution:

Never turn off the printer while the

flashing.

6. Make sure paper is loaded in the printer and click

(Windows) or

nozzle check pattern

(Macintosh). See the section below for instructions on

examining the nozzle check pattern.

If your print quality has not improved, repeat the steps above.

Using the Control Panel

1. Make sure the printer is turned on and not printing, and

that the

black and

2. Press the

cleaning button and hold it for three seconds.

Cleaning takes about two minutes, during which the printer

makes some noise and the

After the cleaning cycle is complete and the

stops flashing, you need to run a nozzle check.

3. Access the Main printer settings dialog box.

4. Click the

tab (Windows) or the

Utility

(Macintosh). You see the Utility menu.

5. Click the

Nozzle Check

instructions on examining the nozzle check pattern.

If your print quality has not improved, repeat the steps above.

Examining the Nozzle Check Pattern

Examine the nozzle check pattern you print. It should look

something like this, with the lower pattern colored cyan,

magenta, and yellow:

W0186B

Each staggered horizontal and straight vertical line should be

complete, with no gaps in the dot pattern. If your printout

looks okay, you're done. If any dots are missing, clean the

print heads again, as explained in the previous sections.

Aligning the Print Heads

If your printouts contain misaligned vertical lines, you may

need to align the print heads. Follow these steps:

1. Make sure the printer is turned on and paper is loaded.

2. Access the Main printer settings dialog box.

18 - EPSON Stylus COLOR 600

power light is

Confirmation

color ink out lights are off.

power light flashes.

power light

button

Utility

icon

See the next section for

Caution:

Load paper that's at least 8.3 inches wide so ink

doesn't spray onto the platen.

3. Click the

tab (Windows) or the

Utility

(Macintosh). You see the Utility menu.

4. Click the

Print Head Alignment

5. Follow the instructions on the screen to print a test page

and select the correct alignment.

Cleaning the Printer

To keep your printer working at its best, you should clean it

several times a year, following these steps:

1. Turn off the printer, unplug the power cord, and

disconnect the printer cable.

Caution:

Don't touch the gears inside the printer.

Never use alcohol or thinner for cleaning; they can

damage the printer components and case.

Don't use a hard or abrasive brush.

Don't get water on the printer components.

Don't spray lubricants or oils inside the printer.

2. Remove all the paper from the sheet feeder.

3. Carefully clean away dust and dirt with a soft, damp cloth.

4. Clean the exterior of the printer with a soft, damp cloth.

Keep the printer cover closed so water doesn't get inside.

5. Clean ink out of the printer's interior with a soft, damp

cloth.

Information Reference List

Engineering Change Notices

Product Support Bulletins

Technical Information Bulletins