Epson Stylus COLOR 900G 제품 정보 매뉴얼 - 페이지 11

{카테고리_이름} Epson Stylus COLOR 900G에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson Stylus COLOR 900G 13 페이지. Epson stylus color 900g: release note
Epson Stylus COLOR 900G에 대해서도 마찬가지입니다: 사양 시트 (2 페이지), 제품 정보 시트 (4 페이지), 릴리스 노트 (1 페이지)

페이지 인쇄

Examining the Nozzle Check Pattern

Examine the nozzle check pattern you print. It should look

something like this:

Each staggered horizontal and straight vertical line should be

complete, with no gaps in the dot pattern. If your printout

looks okay, you're done. If any dots are missing, as shown

below, clean the print head again; see page 10 for instructions.

missing dots

Aligning the Print Head

If your printouts contain misaligned vertical lines, you may

need to align the print head. Your printer must be connected

to a local port, not on a network, to use the Print Head

Alignment utility.

If you are using DOS, follow the instructions in "Aligning the

Print Head Using the Control Panel Buttons" instead.

Follow these steps:

1. Make sure the printer is turned on and letter-size paper is

loaded.

Load paper that's at least 8.27 inches (210 mm) wide.

This prevents ink from spraying inside the printer and

smudging your printouts.

For the best results, load EPSON ink jet paper in the

printer whenever you check the print head alignment.

2. Access the printer settings dialog box.

3. Click the

tab (Windows) or the

Utility

(Macintosh). You see the Utility menu.

4. Click the

Print Head Alignment

5. Follow the instructions on the screen to print a test page

and select the correct alignment.

missing dots

Utility icon

icon.

Aligning the Print Head Using the Control

Panel Buttons

If you cannot use the print head alignment utility program

that came with your printer, follow these steps to align the

print head.

1. Make sure that letter-size or A4-size paper is loaded in the

sheet feeder.

2. While holding down the

P power button to turn on the printer. Then release both

buttons.

3. The S paper out light flashes for about three seconds. While

it is flashing, press the E load/eject button.

The printer prints a sheet of instructions in English, French,

German, Italian, Spanish, and Portuguese explaining how

to align the print heads. Follow these instructions.

load/eject button isn't pressed while the S paper

If the

out light is flashing, the printer enters default-setting

mode. If this happens, turn off the printer and repeat

steps 2 and 3.

4. After aligning the print head, turn off the printer to exit

print head alignment mode.

Cleaning the Printer

To keep your printer working at its best, you should clean it

several times a year. Follow these steps:

1. Turn off the printer, unplug the power cord, and

disconnect the printer cable.

2. Remove all the paper from the sheet feeder.

3. Clean the exterior of the printer with a soft, damp cloth.

4. Clean ink out of the printer's interior with a soft, damp

cloth.

Don't touch the gears inside the printer.

Never use alcohol or thinner for cleaning; they can

damage the printer components and case.

Don't use a hard or abrasive brush.

Don't get water on the printer components and don't

spray lubricants or oils inside the printer.

Don't use any cleaning sheets included with special

media; they may jam inside the printer.

1/99

EPSON Stylus COLOR 900

cleaning button , press the

EPSON Stylus COLOR 900

- 11