Acuity Controls xCella 설치 매뉴얼

{카테고리_이름} Acuity Controls xCella에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Acuity Controls xCella 2 페이지. Wireless keycard

페이지 인쇄

▪

Pick a location near the door where occupants enter and exit

using the key card. A common location is on the wall oppo-

site the door hinges, 3 ft. (92 cm) from the door jamb

WIRELESS KEYCARD

▪

Consider the construction materials in the space and ob-

xCella

stacles that may interfere with RF signals

INSTALLATION GUIDE

™

Installing

1. Decide where you want to mount the key card switch.

The ideal height is in line with wall switches (49" or 125 cm

on center) for comfortable access.

NOTE: If installing over an existing

wall box make sure any bare

electrical wires are capped.

2. Remove the trim plate from the

key card assembly.

3. Using a level and a pencil, lightly

mark two small dots to align the

upper edge of the key card switch.

4. Mount the key card switch securely to the wall using the

provided screws and wall anchors.

A. Using the pencil marks to

ensure it's level, mark the two

mounting screw drill points.

B. Drill two holes for the wall an-

chors with a 3/16" drill bit and

insert the wall anchors.

C. Insert the top screw loosely and

level the Key Card Switch.

D. Insert the bottom screw, and

then hand tighten the top

Key Card Switch • Installation Guide

screw.

5. Insert the trim plate tabs into the

bottom slots of the key card

switch, and then lightly flex the

trim plate to insert the top tabs.

TIP: To remove the trim plate

without marking it, press down

with a fingernail in the top groove

to ease the tabs out of the slots.

6. Insert a key card to test the mechanism.

TIP: There should be an audible

click each time the key card is

inserted or removed.

Linking

Two or more compatible devices can be linked and configured

to provide the desired control. There are two basic types of

devices in the system; transmitters and transceivers.

▪

Transmit-only: Transmitters are simple energy-harvesting

devices that send RF messages to communicate a condition,

level, or state. Transmitters can only be linked to transceivers.

Examples > Self-powered Light Switches, Occupancy Sensors

▪

Transmit & Receive: Transceivers are controlling devices

that send as well as receive RF messages. They also process

relevant control logic, and actuate the appropriate outputs

(switching a light on or off for example). Transceivers can be

estimated time: 10 minutes

Page 1

Linked to a Load Controller

▪

Insert key card: a wireless message is sent to close the cir-

cuits and turn on all linked loads, according to user-defined

program settings.

▪

Remove key card: a wireless message is sent to open the

circuits and turn off all linked loads.

NOTE: For multiple installations, e.g., front and back doors, all

key cards must be removed to send a message.

Troubleshooting

Problem

Solution Checklist

▪

The key card switch

Verify there is an audible click when card is

does not generate a

inserted or removed

▪

message

Verify slot is clear of foreign material or debris.

Use forced air to clean

▪

The linked device

Check for environment or range issues

▪

does not respond

Verify the device is linked

▪

to wireless mes-

Check the transceiver connection and the wir-

sages

ing for errors

▪

Check if appropriate devices are linked accord-

ing to good system planning

902 MHz:

Contains:

FCC: SZV-PTM330U

IC: 5713A-PTM330U

This device complies with part 15 of the FCC rules and Industry Canada ICES-003. Operation

is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause

undesired operation.

IMPORTANT! Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit

pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélec-

trique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.

315 MHz:

Contains

FCC: SZV-PTM33XC

IC: 5713A-PTM33XC

1 of 2