Dillon Precision Products Hunting Equipment 사용 설명서 - 페이지 4

{카테고리_이름} Dillon Precision Products Hunting Equipment에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Dillon Precision Products Hunting Equipment 4 페이지. Dillard's hunting equipment user manual

페이지 인쇄

Dillon Die Instructions, May 2007

Dillon Three-Die Rifle Die Sets

Stuck Case

Remover

Size Die

Carbide

Polished

Expander

to a High

Ball

Micro-Finish

Solid,

1-Piece

Decapping

Standard

7/8 x 14

Threads

Dillon Three-Die Rifle Die Sets Include:

1- Full-Length Size die, nut, priming assem-

bly with carbide expander

1- Seat die, nut, seat stem with nut

1- Crimp die, nut and 1- Spare decap pin

Sizing/Depriming Die

The sizing/depriming die is a full-length

sizing die, manufactured to minimum toler-

ances. We strongly suggest that a head-

space case gage be used to correctly adjust

the size die. Always clean and lube your

rifle cases before attempting to process the

cases (thru the size die).

1. Move the handle down to raise the plat-

form.

2. Screw the sizing/depriming die into sta-

tion one of your reloader.

3. When the die contacts the shellplate,

back the die off 1/2 turn.

4. Use one lubed rifle case to test your siz-

ing and headspace. Readjust the die as

needed to achieve proper headspace.

5. With a case in the die, snug the lock ring.

The depriming assembly includes a car-

bide expander ball for "squeak free," effort-

less neck expansion. In the event of a stuck

case, the design of the depriming assembly

allows it to function as a stuck-case

remover. Simply remove the silver clip,

loosen the stem lock nut and then spin it up

to the top of the stem. With a wrench, turn

the depriming assembly into the die.

"Clockwise" turns will loosen the stuck

case. Use pliers to remove the case from the

depriming assembly.

5/22/07

1:47 PM

Hex adjustments

Precise,

for wrench

Uniform

Taper Crimp

Radiused

Mouth

length (O.A.L.) information.

5. Use only resized, deprimed cases when

setting this die. Move the case to the bul-

let seating station on your reloader

6. Place a bullet on the case and make one

complete stroke of the handle.

7. Check the overall length (O.A.L) of the

test case and bullet using a quality dial

caliper. Adjust the die up or down as

needed.

8. With the case and bullet in the die, snug

the lock ring.

The taper crimp die is configured to cen-

ter both the case neck and case body, there-

by aligning the entire cartridge for a more

uniform crimp.

1. Place the test case/bullet you have into

the crimp station on your reloader.

2. Move the handle down to raise the plat-

form.

3. Screw the taper crimp die into the crimp

station on your reloader.

4. When the die contacts the test case/bullet

move the handle up to lower the platform

5. Turn the die 1/4 to a 1/2 turn "clockwise"

and try crimping your test case/bullet

6. Use a quality dial caliper to measure the

case mouth diameter. Usually, a .002

change is noticed between the neck

diameter and the case mouth diameter.

Adjust as needed.

7. With the test case/bullet in the die, snug

the lock ring.

Refer to the machine operating manual

for any further instructions.

Page 4

Bullet Seating Die

Our bullet seating die is

internally designed to keep the

bullet straight throughout the

seating process.

1. Move the handle down, to

raise the platform.

2. Screw the bullet seating die

into the bullet seating station

on your reloader.

3. Put a sized, empty case into

the shellplate under the seating

die. Pull the handle down.

Screw the seat die body down

until it stops, then back it up

1/8 of a turn.

4. Refer to your rifle loading

manual for proper overall

Taper Crimp Die