Dilog DSH-710 빠른 시작 매뉴얼

{카테고리_이름} Dilog DSH-710에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dilog DSH-710 2 페이지.
Dilog DSH-710에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지)

페이지 인쇄

Safety

Please carefully read this guide before you connect your box. For a complete guide, visit www.dilog.se. Save this guide

for later use. Always place the box on a flat, clean, dry surface. If the box is somehow damaged, it should always be

examined by a dealer before being used again. Always unplug the power to the box if you must travel away or there is a

risk of thunder. Any cleaning is done with a damp cloth and mild soap.

Warning!

Never open the box cover as you can damage both yourself as well as the electronics. Make sure there is plenty of space

around the box where it is placed so that proper ventilation can be achieved. Do not block the box ventilation holes in any

way. Do not place the box in a tight cabinet or on top of other equipment that generates heat.

Environment

This product is made with respect to our environment. It is designed to have low power consumption, reduced use of

environmentally hazardous substances, increased opportunities for recycling and easy handling during recycling.

Consequently, the box should be handed over to recycling center that handles electronic scrap when considered

exhausted.

Power source

This box is designed to be powered from a wall outlet with a rated voltage 230V 50Hz. Do never remove the cover of the

box yourself as it has live parts and can cause serious injury.

All service/ repair should be performed by Dilog Nordic AB

Liquid

The box should not be exposed to moisture or water, never place any type of liquid on or next to the box.

Should the box be exposed to liquid, immediately disconnect the power cord and contact the dealer.

• Do not leave your box or remote control in a place exposed by direct sunlight.

• The box should be placed on a flat, stable surface.

• The box should not be installed in areas with high humidity.

• Place the box in a place with good air circulation, the box should not be placed in closed cabinets, or under other devices.

• Connect the cables to other devices, before connecting the power to the box.

• Replace dead batteries for the remote control immediately after they run out and remove the batteries if you will not

use the box for some time. The remote control can be damaged due to leakage from old batteries.

• If you move the unit from an environment of low temperature, wait to plug it in until it reaches room temperature.

First-time installation

When you start the box for the first time the installation guide

appears. First, select language.

Under Mode, select "DVB Mode" to receive only from satellite,

"IP" to only receive via IP or "Hybrid" to to receive both via

satellite and IP.

Mark "Select" and press OK button on the remote.

Make sure that the satellite you intend to take the signal from

is selected (for SVT World; Eutelsat 9A or Thaicom 5).

Check that the frequency, polarization and symbole rate

complies with the correct satellite (these values are preset

correctly for Eutelsat 9A but not for Thaicom 5 or other satellite

positions).

Select "Start" and press the OK button on the remote.

You will now be able to make settings for your particular

configuration, select "Setup" and press OK on the remote.

Set the LNB type, and configure DiSEqC to correct input for

the LNB aimed for the satellite position, make sure to have

good signal quality and signal strength shown as two green

bars.

Mark "Select" and press the OK button on the remote to start

the channel search.

Quick Start Guide

Dilog DSH-710

Connect to the HD TV

Connect to the cable signal.

Video/audio input jack

Connect to Ethernet

with an Ethernet cable

Connections

Connect to the antenna input of

another device, such as a TV

Connect the coax cable

Connection to

Connect to the HD TV

from the dish/LNB

Network/Internet.

Connect to the cable signal.

Connect to the HD TV

Video/audio input jack

Connect to the cable signal.

Video/audio input jack

Connect to Ethernet

For connection to TV

Connect to HDMI input on the TV.

with an Ethernet cable

Connect to the antenna input of

Connect to Ethernet

or other digital TV box.

another device, such as a TV

HDMI connection is to prefer, gives the best quality.

another device, such as a TV

with an Ethernet cable

Connect to the antenna input of

another device, such as a TV

Connect to the cable signal

Version 2013-08-27

Connect to a digital audio component

with OPTICAL cable

Socket to connect

SCART/Composite

adapter.

Socket to connect

Connect to the HD TV

compatible USB

Connect to the cable signal

Connect to the HD TV

fixings/devices.

Video/audio input jack

Connect to the cable signal

Video/audio input jack

Connect to a digital audio component

Connect to Ethernet

with OPTICAL cable

Connect to a digital audio component

with an Ethernet cable

Connect to a digital audio component

Optical digital output to

Connect to Ethernet

with OPTICAL cable

connect to HI-FI or home

with an Ethernet cable

theater.

Connect power to

box with the power

adapter.