Motorola AX 사용자 설명서 - 페이지 2

{카테고리_이름} Motorola AX에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Motorola AX 2 페이지. Two-way business radio

Scan

Scan allows you to monitor multiple channels and receive calls that are transmitted on them. Two types of scan are supported: Normal

Scan and Priority Scan.

Normal Scan searches all channels sequentially in the radio's scan list, whereas Priority Scan allocates 50% of the scanning time to the

Priority Channel (the first channel in the designated scan list).

Start

Ch. 2

Ch. 3

Ch. 2

Normal Scan

Ch. 1

Channel 1 Prioritized

Ch. 4

Home

During scan, when activity is detected that meets the unsquelch condition, the radio stops scanning and switches to that channel; the

G indicator is illuminated, and the channel number is displayed. When no activity is detected for a pre-set time, the radio resumes

scanning.

If your radio has switched to a non-priority channel during priority scan, it still checks for activity on the priority channel. If activity is

detected there, the radio switches to the priority channel.

The radio transmits on the Prime Channel, if PTT is pressed during scanning. If the radio has stopped scanning, and changed to a

particular channel, all transmit and receive activity is performed on that channel.

• Press the Scan button to begin channel scanning. The G indicator blinks to indicate that the radio is scanning. The LCD Screen

shows the Prime Channel where the scan began.

• Press the

button to scan the channels in incremental order, and the button to scan in the opposite order.

• Press Scan button to stop scanning.

Deleting a Nuisance Scan Channel

A channel with unwanted activity is called a Nuisance Channel. You can remove a Nuisance Channel from the scan list temporarily. To

remove a Nuisance Channel

• Press the Nuisance Channel Delete button, when your radio stops on a Nuisance Channel. A high-pitched tone is heard.

You cannot remove the Prime or Priority Channel from the scan list. If attempted, a low-pitched tone is heard, and no action is taken.

To reinstate the deleted channel(s) into the scan list, restart scan, or simply turn off your radio and turn it on again.

Programming Mode

This mode allows you to change feature parameters to enhance the use of your radio.

Entering Programming Mode

If your radio is turned on, turn it off. Press and hold the Monitor button, and turn on your radio. A ringing tone is heard, indicating that your

radio is in Programming Mode. The K indicator illuminates and RW is displayed.

Exiting Programming Mode

Turn off the radio, to exit Programming Mode.

Accessing Programming Mode Parameters

Press PTT to scroll forward or the Monitor button to scroll backwards through the features available in the Programming Mode. Press the

button to scroll through the parameters for each feature.

Feature

Range

Squelch Level

SQL-00, ..., SQL-15

Select low level when you need to receive very weak

(SQL-XX)

signal, and select high level when the communications distance is near.

Scan List 1

1-01-XXX, ...,

Up to 16 members per scan list. First member is assigned as Priority Channel,

(SCANLST1)

1-16-XXX,

if Priority Scan is started. When scanning is started, only these 16 members

XXX denotes channel number.

will be scanned.

Time Out Timer

TOT-OFF, TOT-001, ..., TOT-010

This determines the maximum duration (in minutes) that you can transmit

(TOT-XXX)

continuously.

Battery Saver

BS-OFF,

Battery Saver helps to extend your battery life. When enabled, it turns off

(BS-XXXX)

BS-NORM,

radio receiver circuitry periodically when no activity is detected. BS-NORM

BS-ENH

(Normal) turns off the radio less frequently; select this if you want to save bat-

tery, but expect a Selective Call. BS-ENH (Enhanced) turns off the receiver

for a longer duration; select this if you want to maximize battery saving and

do not expect to receive any Selective Call.

Battery Type

BT-NIMH,

Selects the type of battery that your radio uses: NIMH (Nickel Metal

(BT-XXXX)

BT-NICD,

Hydride), NICD (Nickel Cadmium) or ALK (Alkaline).

BT-ALK

Alert Tone Volume

BEEP-OFF, BEEP-1,

Selects the alert tone volume needed. Select BEEP-OFF, if you require quiet

(BEEP-X)

BEEP-2,

operation, or BEEP-3, if working in a noisy environment.

BEEP-3

Prime Channel Select

PRM-OFF, PRM-001, ....,

The Prime Channel is the channel that you wish to spend most of your time

(PRM-XXX)

PRM-XXX,

monitoring. The radio will always switch back to the Prime Channel if it is

XXX denotes the highest channel

idle for more than the pre-programmed hang-time in other channel.

number supported by your model.

Backlight Select

LGT-AUTO, LGT-TOGL

Selecting LGT-TOGL makes the Backlight button a toggle to control the ON/

(LGT-XXXX)

OFF status of the LCD backlight. Selecting LGT-AUTO causes the backlight

to automatically extinguish, if there is no keypress for more than 5 seconds.

Pressing the Backlight button prolongs illumination time.

Refer to this table for the frequencies and codes for your radio:

Frequency/Code Table

Frequency (MHz)

Channel

AXU4100–UHF AXV5100–VHF

Ch. 1

Ch. 3

464.5000

Ch. 1

464.5000

Ch. 4

464.5000

464.5500

LED Indicators

LED Color

State

Red

Illuminated Radio is transmitting.

Red

Blinking

Green

Illuminated Radio is receiving.

On/Off and Volume Knob

• If the radio is off, turn this knob clockwise to turn

the radio on.

• If the radio is on, turn this knob counter-clockwise

to turn the radio off.

• Turn this knob clockwise to increase the volume.

• Turn this knob counter-clockwise to decrease the

volume.

Monitor Button

• Used to monitor the channel for any

activity; squelch is disabled.

Remarks

Push-to-Talk (PTT) button

• Press and speak to microphone to send

message.

• Release and listen to receive messages.

Button

• Used to select a channel in Normal

Mode.

• Used to select a parameter in Program-

ming Mode.

• Used to change the scanning direction.

Microphone

• Speak into the microphone when send-

ing message.

Speaker

• You will hear received messages through

the speaker.

Code (Hz)

151.6250

67.0

151.6250

77.0

151.6250

88.5

151.6250

179.9

151.6250

None

151.9550

67.0

151.9550

82.5

151.9550

94.8

151.9550

179.9

151.9550

None

Indication

Battery voltage is low.

LCD Screen

• Displays selected channel, programming parameters, status messages and any error or information messages.

LCD

Description

Indicator

Keypad lock indicator

Illuminates when your keypad is locked.

Talkaround indicator

Illuminates when you are not transmitting through the repeater. Extinguishes

when you are transmitting using the repeater offset/user-defined transmit

frequency.

Battery level indicator

Shows remaining charge in battery based on how many bars are displayed.

Power level indicator

"L" illuminates to indicate radio transmits in low power; "H" illuminates to

indicate radio transmits in high power.

Monitor indicator

Illuminates when monitoring a selected channel.

Programming Mode

Illuminates when in Programming Mode.

indicator

Scan indicator

Blinks, without the dot, when scan is activated. Illuminates when there is

some activity on a non-priority channel. Illuminates, with dot blinking,

indicates that there is some activity on the priority channel.

Signal Strength Indicator

Shows the signal strength. Six bars indicate the strongest signal.

Programming Port

• Lower port of the radio.

• Used to program your radio.

Programmable Buttons (A, B, C, D)

• Used to select various functions. These functions can be assigned as a short press (press and release) or a

long press (press and hold for 1 second).

Button

Toggles display between Channel Number and Channel Alias.

Channel Alias

Backlight

Toggles backlight display between On and Off.

Locks or unlocks all buttons except PTT, Monitor and On/Off/Volume Knob.

Keypad Lock

Nuisance Channel

Removes unwanted channel(s) temporarily from scan list during scan.

Delete

Enables or disables radio from requiring matching PL/DPL to unsquelch.

PL/DPL Enable

Prime Channel

Quick move to the pre-programmed "Prime" channel

Selects required power level: High or Low.

Power Select

Starts or stops channel scan.

Scan

Squelch Level

Selects desired squelch level. Use the

unsquelch radio unconditionally, whereas Level 15 will set tightest squelch).

Talkaround

Enables or disables radio to transmit in Talkaround mode.

No Operation

No function is programmed to this button.

Selects the alert tone volume needed for quiet operations or a noisy environment.

Alert Tone Volume

1. Parameter values are preserved, even after the radio is turned off.

2. Turning off the radio or changing the channel restores this setting to the default value of the active channel.

• The default functions programmed to your radio are described in the table below.

Press Type

Button A

Short Press

Prime Channel

Long Press

Channel Alias

• Although your radio is programmed with default functions, you have the ability to re-program the radio's

programmable buttons. You may want to write down the new functions in the table below.

Press Type

Button A

Short Press

Long Press

Function

Accessory Connector

• Used to connect compatible

accessories to your radio.

Function

button to choose desired level (Level 0 will

Button B

Button C

Button D

Scan On/Off

Power Select

Backlight On/Off

Nuisance Channel

No operation

Kepad Lock

Delete

Button B

Button C

Button D