diLUSSO DW260GS 지침 및 사용 설명서 - 페이지 11

{카테고리_이름} diLUSSO DW260GS에 대한 지침 및 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. diLUSSO DW260GS 12 페이지.

페이지 인쇄

Once the appliance has been installed, the power supply cable and the electrical socket should

be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be replaced by the manufacturer or its Technical

Assistance Service in order to prevent all potential hazards.(See Assistance)

The company shall not be held responsible for any incidents that occur if these regulations are

not observed.

Advice regarding the first wash cycle

After the appliance has been installed, immediately before running the first wash cycle, completely

fill the dispenser of rinse (see Rinse aid ).

Positioning the Appliance

Position the appliance in the desired location. The back should rest against the wall behind it, and

the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and

drain hoses that can be positioned to the right or the left to facilitate proper installation.

Leveling the Appliance

Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the height of the

dishwasher, making it level. In any case, the appliance should not be inclined more than 2°.

NOTE:

The maximum adjustment height of the feet is 20 mm.

How to Drain Excess Water From Hoses

If the sink is 1000mm higher from the floor, the excess water in hoses cannot be drained directly

into the sink. It will be necessary to drain excess water from hoses into a bowl or a suitable

container that is held outside and lower than the sink.

Water Outlet

Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.

Ensure that the water inlet hose is not kinked or squashed.

Extension Hose

If you need a drain hose extension, observe to use a similar drain hose..

It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be

reduced.

Syphon Connection

The waste connection must be at a height of between 50cm (minimum) and 100cm (maximum)

from the bottom of the dish. The water drain hose should be fixed by a hose clip.

Start of Dishwasher

The followings should be checked before starting the dishwasher:

1 Whether the dishwasher is level and fixed

2 Whether the inlet valve is opened

3 Whether there is leakage at the connections of the conducts

4 Whether the wires are tightly connected

5 Whether the power is switched on

6 Whether the inlet and drain hoses are knotted

7 All packing materials and printings should be taken out from the dishwasher

Attention

After installation, please put this manual into the bags of printings.

The content of this manual is very helpful to the users.

9. Troubleshooting Tips

Error codes

When some malfunctions happen, the appliance will display error codes to warn you.

Codes

Meanings

Door open

LED1、 LED2 flash

Water inlet

LED1、 LED4 flash

LED1、 LED5 flash

Water drainage

LED1、 LED6 flash

Temperature sensor

Overflow/leakage

LED2、 LED3 flash

LED2、 LED4 flash

Water leakage

Heating element

LED2、 LED5 flash

LED1 LED2 LED3 LED4 LED5 LED6

Intensive

WARNING!

If overflow occurs, turn off the main water supply before calling a service. If there is water in the base

pan because of an overfill or small leak, the water should be removed before restarting the dishwasher.

Possible Causes

The door is opened when the

dishwasher is operating

Water inlet malfunction

Water drainage malfunction

Temperature sensor malfunction

Overflow occurs/Water leakage occurs

Water leakage occurs

Abnormal heating

Heavy

Normal

Rinse

Rapid

Soak

sec

Dry+