Motorola KEM-ML34301B 사용자 설명서 - 페이지 3

{카테고리_이름} Motorola KEM-ML34301B에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Motorola KEM-ML34301B 5 페이지. Mt series

페이지 인쇄

1. Follow the steps above to install a NiMH Battery Pack.

2. Plug the AC power supply cord into the jack on the desk

stand.

3. Plug the AC power supply into a standard wall outlet.

4. With a radio facing forward, slide it into one of the charging

pockets.

5. When charging in the battery charger, the red light on the

charger base will glow continuously.

Turning your Radio On and Off

Turn

clockwise to turn the radio on and counterclockwise to

turn the radio off.

1. In the ON position, the radio chirps and briefly shows all

feature icons available on the radio.

2. The display screen then shows the current channel, code

and all features that are enabled.

Setting the Volume

Press and hold

for three seconds, then rotate

reach a comfortable listening level.

1. Rotate

clockwise to increase the volume.

2. Rotate

counterclockwise to decrease the volume.

Do not hold the radio close to your ear. If the volume is set to an

uncomfortable level, it could hurt your ear.

Talking and Listening

To communicate, all radios in your group must be set to the

same channel and Interference Eliminator Code.

1. To talk, press and hold

2. When you are finished talking, release

For maximum clarity, hold the radio two to three inches away

from your mouth and speak directly into the microphone. Do not

cover the microphone while talking.

Talk Range

Your radio is designed to maximize performance and improve

transmission range. Do not use the radios closer than five feet

apart.

Power Boost

To boost your radio's power up to high power, press the top

portion of the

button when talking. If you know your party is

close by, you can conserve your battery's energy by pushing the

lower part of the

button to use less power.

Note: If you are on an FRS only channel (see Channels and

Frequencies table) the radio will only use low power when either

portion of the

is pressed.

Monitor Button

Pressing and holding

for three seconds allows you to listen

to the volume level of the radio when you are not receiving. This

allows you to adjust the volume, if necessary. You can also

press

to check for activity on the current channel before you

talk.

Push to Talk

Timeout Timer

To prevent accidental transmissions and save battery life, the

radio emits a continuous warning tone and stops transmitting if

you press

for 60 continuous seconds.

Menu Options

Selecting the Channel

Your radio has 22 channels. The channel is the frequency the

radio uses to transmit. Channels 8-14 are FRS 0.5 watt only and all

other channels are GMRS. (See the "Channels and Frequencies"

table on overleaf for details.)

1. With the radio on, press

. When the radio is on a 0.5

watt channel,

displays. When the radio is on a 1.5 watts

channel,

displays. The current channel flashes.

2. Press

and select an unused or quiet channel.

3. Press

to save the channel setting or

up.

Selecting the Interference Eliminator Code

Interference Eliminator Codes help minimize interference by

blocking transmissions from unknown sources. Your radio has

121 Interference Eliminator Codes. Codes 1 – 38 are the

standard analog codes that appear on other FRS/GMRS radios.

Codes 39 – 121 are additional digital codes added for superior

interference protection. 0 is the off position, no analog or digital

codes are enabled.

To sett he code f ora channel :

1. Press

until the code starts to flash.

2. Press

3. Press

to save the code setting or

You can set a different code for each channel using this

procedure. An extended press of

through the Interference Code rapidly so you can quickly reach

the code you want.

Note: You must set the Interference Eliminator Code to 0 on a

radio that uses Interference Eliminator Codes to communicate

with radios that do not have Interference Eliminator Codes.

Select 0 for "no tone, no code" and OFF will flash on your radio's

until you

display.

Setting and Transmitting Call Tones

Your radio can transmit different call tones to other radios in

your group so you can alert them that you want to talk. Your

radio has 20 call tones from which to choose.

To seta cal lt one:

1. Press

three times until the current call tone setting

flashes and

2. Press

3. Press

to set the new call tone or

To transmit your call tone to other radios set to the same

channel and Interference Eliminator Code as your radio,

press

Note: Setting the call to 0 disables the call tone feature.

Hands-Free Use Without Accessories (

You can use the iVOX feature to transmit hands-free without the

need for any headset accessories. Once iVOX is turned on, the

radio detects your voice and transmits when you speak into the

internal microphone.

1. Press

until

setting On/Off will flash.

2. Press

3. Press

to set or

Hands-Free Use With Accessories (

You can transmit hands-free more reliably with the use of

optional headset accessories. Once VOX is turned on, the radio

detects your voice and transmits when you speak.

Many accessories (sold separately) are available for your radio.

For more information, visit our Web site at

motorolasolutions.com/talkabout.

1. Turn the radio off and plug the VOX accessory into the

accessory port.

2. Turn the radio on. VOX shows on the display.

3. Adjust the volume appropriately by rotating

volume before placing the accessory on your head or in your

ear.

4. To turn off, simply remove accessory.

Note: There is a short delay between the time you start talking

and when the radio transmits. There is a short delay before the

transmission is completed.

Setting the Sensitivity Level When in

Adjusting the radio's sensitivity level helps minimize the

possibility of unintended noises triggering a transmission and

helps the radio pick up soft voices.

1. Press

until VOX and the level setting (1 - 3) appear on

the display.

2. Press

3. Press

to set or

to continue set

3 = High Sensitivity for quiet environments

2 = Medium Sensitivity for most environments

1 = Low Sensitivity for noisy environments

Emergency Alert

to select the code.

to continue set up.

Volume

allows you to scroll

Push to Talk

(High)

Push to Talk

appears.

to change and hear the call tone.

(Low)

to continue set up.

Call Tone

Flash Light

Button

)

Scroll/Weather

Microphone

appears on the display. The current

Mini-USB

to select On or Off.

Charging Port

to continue set up.

)

. Lower the

Mode

to select the sensitivity level.

to continue set up.

Note: When you connect a headset, the radio is automatically

set to the last chosen sensitivity level.

Noise Filtering

The Q

noise-filtering feature helps to ensure uninterrupted

communication with other Motorola radios that have this

feature. This feature also filters out unwanted transmissions

from other radios. This is useful in places where there is

heavy radio traffic, such as amusement parks or ski resorts.

Note: Q

noise filtering is not available when the radio is

scanning.

To t ur n Q

noi se f i l t er i ng on orof f :

1. Press

until

displays. The current setting On/Off will

flash.

2. Press

to turn noise filtering On or Off.

3. Press

to confirm your selection or

up.

To t r ansm i tt o a r adi o t hathasQ

noi se f i l t er i ng t ur ned on:

1. Select the same channel and Interference Eliminator

Code as the other radio.

2. Press

to send a call tone. This allows your voice to

pass through the Q

noise filter on the receiving radio.

3. Press

and speak normally.

Note: If you skip step 2, the beginning of your message may

not be heard on the receiving radio. For a 30-second period,

starting after the last transmission, all transmissions

received on the selected channel and code will pass

through the Q

noise filter.

VibraCall

Alert

VibraCall

is a vibrating alert that notifies you that your radio is

receiving a message. This is useful in noisy environments. When

the alert is on, the radio vibrates once every 30 seconds when

you receive a message on the channel and code you set.

1. To turn vibrating alerts on, press

until

current setting will flash.

2. Press

to change the setting to On/Off.

3. Press

to set or

to continue set up.

Keypad Tones

You may enable or disable the speaker key tones. You will hear

the key tone each time a button is pushed.

1. Press

until

appears. The current setting On/Off will

flash.

2. Press either

to turn On or Off.

3. Press

to confirm or

to continue set up.

Note: When the key tone feature is off, the following are not

disabled:

•

Transmit timeout alert tone

•

Call tone

•

Low battery alert tone or

•

The transmitted talk confirmation tone

Transmitting a Talk Confirmation Tone

You can set your radio to transmit a unique tone when you finish

transmitting. It is like saying "Roger" or "Over" to let others

Numbers for Channel,

know you are finished talking.

Call Tone

1. With the radio on, press

until the

current setting On/Off flashes.

Numbers for Codes

2. Press

to turn On or Off.

3. Press

to set or

to quit menu mode.

—Battery Meter

Dual Watch Scan

This feature allows you to monitor two channels at the same

—Channel Power

time.

Indicator

1. Press the

button until the Dual Channel Scan icon

(see menu Options)

displays.

2. Press the

buttons to select the second channel for

—Keypad Lock

Dual Watch reception. (if you want to disable the Dual

Watch function, set it to 'OFF').

—Talk Conﬁrmation

Tone (Roger Beep)

3. Press

or the PTT button to confirm the channel selection.

When the Dual Watch feature is activated, the radio will switch

—Noise Filtering

sequentially between the primary and the Dual Watch channels.

—On/Off for each

The active channel will display for five (5) seconds after any

feature

activity has ended on the dual channel. You may talk on the Dual

Watch channel during this period.

to continue set

MON

is displayed. The

appears. The

—Vibr

—Scan

—Dua

—Call

Keyp

—Wea

—Han

With

Acce

—Han

With

MT Series