Motorola D1002 사용자 설명서 - 페이지 11
{카테고리_이름} Motorola D1002에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Motorola D1002 26 페이지. Digital cordless phone
Motorola D1002에 대해서도 마찬가지입니다: 사용자 설명서 (45 페이지), 사용자 설명서 (26 페이지), 사용자 설명서 (50 페이지)
페이지 인쇄
3. Using the phone
Calls
Make a call
<
1. Press
.
2. Dial the telephone number.
Pre-dial
1. Enter the phone number (maximum 24 digits). If you make a mistake press
<
2. Press
to dial the phone number entered.
Dial one touch numbers 1 to 9
1
9
1. Press and hold a key from
to
until the number is displayed and dialled.
-
If no number is stored, you hear a beep.
Call from the phonebook
d
1. Press
. The first entry in the phonebook is displayed.
u
d
2. Scroll
or
to the entry you want.
<
3. Press
to dial the number.
TIP
Instead of scrolling to browse the phonebook entries, press the numeric key corresponding to the
first letter of the entry you wish to locate. For example, pressing
2
with A. Pressing
again will show the entries starting with B, etc...
Call from the calls list
NOTE
You need to subscribe to your network's Caller Line Identification service to be able to see the
caller's number in the calls list. See "Calls list" on page 14 for more details.
u
1. Press
to enter
CALL LOG
menu. You have the options to access
CALL
LIST. The first entry in the call list is displayed.
u
d
2. Scroll
or
to the entry you want.
<
3. Press
to dial the number.
Answer a call
1. When the phone rings and
flashes in the display, press
call via the loudspeaker.
WARNING
When the phone is ringing, avoid holding the earpiece too close to your ear as it may damage your
hearing. Handsfree activation can suddenly increase the volume in the earpiece to a very high
level. Make sure the handset is not too close to your ear.
NOTE
If you have subscribed to your Network's Caller Identity service and assigned a VIP Group to the
caller's number, the caller's details are displayed before the phone starts ringing (see "Store an
entry" on page 12 and "Group melody" on page 16). You can set your phone to give the default
ringtone as soon as the call is received then once the caller's identity is displayed, the assigned
ringtone will start. See "First ring" on page 17.
Using the phone
TIP
If Auto Pick up mode (see page 17) is on, simply lift up the handset from its base to answer the
call. The default setting is On.
NOTE
An incoming call has priority over other events. Whenever there is an incoming call, other
operations in progress such as phone settings, menu navigation, etc. will be ended.
Adjust volume
1. During a call, press
e
.
Mute
Mute the microphone so that you can talk to someone else in the room without your caller hearing
you.
1. During a call, press
2. Press
End a call
1. Press
After you hang up, the duration the phone is off-hook is displayed for 5 seconds.
NOTE
2
will show the entries starting
If auto hang-up is on (see page 17) simply replace the handset on the base to end the call. The
default setting is ON.
Switch handset on/off
1. Press and hold
2. Press and hold
m
CALL
LIST. Press
to enter
Call a second external number
Put an external caller on hold to make a second external call. You can then switch between both
callers or hold a 3-way conference call.
1. During your call, press
<
v
2. Press
or press
to answer the
3. Enter the second number.
4. When your second caller answers, press
5. Press
Intercom
This feature is only available when there are at least 2 registered handsets. It allows you to make
internal calls, transfer external calls from one handset to another and use the conference option.
u
d
or
to adjust the earpiece or loudspeaker volume.
-
The level is shown in the handset display.
e
.
-
The microphone is muted.
e
again to turn the microphone back on.
>
.
>
until the handset switches off.
>
again to switch the handset back on.
m
d
. Scroll
to
INIT 2ND
m
.
-
Display shows
CALLING R
m
m
CONFERENCE
– press
to initiate a 3-way with an external caller and internal caller.
m
SWITCH CALLS
– press
to switch between the two callers.
>
to hang up.
CALL.
to open the option menu:
11