Motorola D1103 사용자 설명서 - 페이지 17
{카테고리_이름} Motorola D1103에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Motorola D1103 46 페이지. D1100 series
Motorola D1103에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지)
페이지 인쇄
NOTE
If only one handset is registered the display prompts "Not
available" and returns to the previous screen. You must register
additional handsets before the handsets will be displayed and
make Internal calls.
NOTE
If the Room Monitor is triggered to call a handset or number and
the called handset is on a call, an alert tone of 3 beeps will be
heard. If the Room Monitor is triggered continuously the alert
beap will be emiitted every 5 seconds.
WARNING
This product is not intended for use as a baby safety device and
is not a substitute for adult supervision.
Using additional handsets
12. Using additional handsets
You can use up to five D1100 additional handsets with your
D1100 base to extend your phone system without needing to
install extension sockets for each new phone.
Your D1100 handset can also be registered to up to 3 other
bases. You can then select the base you would prefer to use.
If you have purchased a D1100 multiple pack any additional
handsets come pre-registered to the base.
If you have purchased an additional handset separately you
must register it to your D1100 base before it can be used.
Registering an additional handset
At the base:
p
1. Press and hold
for 2 seconds until the base Power
starts flashing. The base will remain in registration mode for
90 seconds.
At the handset:
1. If the handset is new and the display shows
u
Menu
Registration
Select
Press
. Scroll
to
. Press
Or
If the handset has already been registered to another base
Menu
the standby display is shown. Press
, scroll
Registration
Select
and press
.
Register Handset
Select
2.
is highlighted. Press
.
u
3. Bases are displayed. If necessary, scroll
or
base you wish to register your D1100 handset to and press
Select
.
OK
4. Enter the system PIN and press
. (Default setting =
0000)
Searching Base X
5. The display shows
(where X is the chosen
Handset Registered
base number) then
.
The handset is automatically assigned the next available
handset number.
If registration is not successful first time, please repeat the
process again in case the base registration period ran out of
time.
If there are already 5 handsets registered to the base, the
registration will fail. You must de-register another handset before
you can register the new one.
Select a base
If your D1100 handset is registered to more than one base, you
can select which base to use.
u
d
Menu
1. Press
, scroll
or
d
Select Base
2. Scroll
to
and press
3. All base numbers are displayed.
where the handset was previously registered to. Scroll
d
to the base you want and press
Searching Base...
4. Display shows
that base.
De-register a handset
Use one handset to de-register another. You cannot de-register
the handset you are using.
u
d
Menu
1. Press
, scroll
or
d
De-register
2. Scroll
to
and press
3. Enter the system PIN and press
0000)
u
d
4. Scroll
or
to the handset you want to de-register and
Please Register
Select
.
press
.
.
Yes
No
5. Press
to confirm or
Back
6. Press
to return to the previous menu level or
return to standby.
u
d
or
to
d
to a new
Registration
Select
to
and press
.
Select
.
(In use)
is added to bases
u
or
Select
.
. then the standby display for
Registration
Select
to
and press
.
Select
.
OK
. (Default setting =
to cancel.
>
to
17