Motorola GM160 서비스 정보 - 페이지 14

{카테고리_이름} Motorola GM160에 대한 서비스 정보을 온라인으로 검색하거나 PDF를 다운로드하세요. Motorola GM160 32 페이지. Professional radio
Motorola GM160에 대해서도 마찬가지입니다: 서비스 정보 (34 페이지), 사용자 설명서 (44 페이지), 기본 서비스 매뉴얼 (46 페이지), 서비스 정보 (32 페이지), 사용자 설명서 (44 페이지)

페이지 인쇄

2-8

3.9

Speaker

The controlhead contains a speaker for the receiver audio. The receiver audio signal from the

differential audio output of the audio ampliﬁer located on the radio's controller is fed via connector

J0801-10, 11 to the speaker connector P0801 pin 1 and pin 2. The speaker is connected to the

speaker connector P0801. The controlhead speaker can be disconnected if an external speaker,

connected on the accessory connector, is used.

3.10

Electrostatic Transient Protection

Electrostatic transient protection is provided for the sensitive components in the controlhead by

diodes VR0811 VR00812 VR0816 - VR0817. The diodes limit any transient voltages to tolerable

levels. The associated capacitors provide Radio Frequency Interference (RFI) protection.

4.0

Controlhead Model for GM380, and GM1280

The controlhead contains the on/off/volume knob, the microphone connector, several buttons to

operate the radio, several indicator Light Emitting Diodes (LED) to inform the user about the radio

status, and a Liquid Crystal Display (LCD) with 21 pre - deﬁned symbols and a 32*96 dot matrix for

graphical or alpha - numerical information e.g. channel number, select code, call address name. To

control the LED's and the LCD, and to communicate with the host radio the controlhead uses the

Motorola 68HC11K4 microprocessor.

4.1

Power Supplies

The power supply to the controlhead is taken from the host radio's FLT A+ voltage via connector

J0801 pin 3. The voltage FLT A+ is at battery level and is used for the LED's, the back light, to power

up the radio via on / off / volume knob and to supply the voltage regulator circuitry. The regulator

circuitry provides the stabilized +5 volts which is used for the microprocessor circuitry, the display,

the display driver and the keypad buttons. The regulated +5V taken from the host radio via connector

J0801 pin 7 (line 5V SOURCE) is only used to switch on or off the voltage regulator in the control-

head.

4.2

Voltage Regulator Circuit

Voltage regulator U0861provides 5V for the controlhead. The supply voltage FLT A+ for the voltage

regulator is fed via parallel resistors R0861/2 and dual diode D0861 to pin 8 of U0861. The +5 volt

output is switched on and off by the host radios's 5 volt source via line 5V SOURCE and control

transistor Q0866. When the host radio is switched off the voltage on line +5V SOURCE is at ground

level and switches off transistor Q0866. Pull up resistor R0863 pulls input SHUTDOWN (pin 3) of the

voltage regulator U0861 to FLT A+ level and switches off the output of U0861 (pin 1). When the host

radio is switched on the voltage on line 5V SOURCE of about +5 volts switches on transistor Q0866

which in turn pulls input SHUTDOWN (pin 3) to ground and switches on the output of U0861. Input

and output capacitors (C0861 / C0862 and C0864 / C0865) are used to reduce high frequency noise

and provide proper operation during battery transients. Diode D0861 prevents discharge of C0862

by negative spikes on the FLT A+ voltage. This regulator provides a reset output (pin 5) that goes to

0 volts if the regulator output goes out of regulation. This is used to reset the microprocessor

(U0871) and the display driver (J0821-5) to prevent improper operation.

The voltage USW 5V derived from voltage FLT A+ is stabilized using resistor R0855 and diode

VR0855 This voltage is used to buffer the microprocessor's internal RAM. C0856 allows the battery

voltage to be disconnected for a couple of seconds without losing RAM parameters. Diode D0855

THEORY OF OPERATION