Epson LabelWorks LW-300 사용자 설명서
{카테고리_이름} Epson LabelWorks LW-300에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson LabelWorks LW-300 9 페이지. Epson lw-300
Epson LabelWorks LW-300에 대해서도 마찬가지입니다: 사용자 설명서 (2 페이지), 사용자 설명서 (1 페이지), 공지 사항 (4 페이지), 매뉴얼 (1 페이지), 범위 매뉴얼 (7 페이지)
페이지 인쇄
User's Guide
*412092100*
*412092100*
Read these instructions before using your product.
Button names and functions
1
2
3
4
5
6
7
8
9
1.
Power
2. Font
3. Font size
4. Font style
5. Settings
6. Character keys
7.
Shift key
8. Caps lock
9. Accent
10. Space
11. Shift key
12. Select/Enter
13. Punctuation
14. Symbols
15. Delete (
+
16. Preview
17. Print copies
18. Cursor keys (
+
next label)
19. Print (
+
feeds the tape)
20.
Cut button
21. Display
Turning the power off
Press
to turn off the power. If using an AC adapter,
disconnect it from the wall outlet and the product. If
batteries are inserted, remove them only if the product
will not be used for a long period of time.
Display indicators
Indicators on the display show whether or not settings
are enabled.
11
10
1.
Font size
2. Font width
3. Frame
4. Font style
5. Vertical text
6. Battery level
7.
Cursor (blinks to indicate current position)
8. Line number (appears when multiple lines exist)
Note: You can print up to two lines of text.
9. Accent mark options
10. Upper/lower case
11. Label number (you can save up to 30 labels)
deletes all text)
,
+
goes to previous or
1
2 3 4 5
9
8
7
6
Display settings
You can adjust the following display settings.
Contrast: Adjusts the density of the fonts on the display.
(Value: -5 to +5)
Language: Changes the language of the settings and
messages on the display.
inch:cm: Selects the unit of measurement.
To adjust display settings, follow the steps below:
1. Press
to turn on the product.
+
2. Press
3. Press
press
to select it.
4. Press
press
.
.Setup
This product operates with batteries (not included) or
with an AC adapter (not included).
Inserting batteries
1. Remove the rear cover.
2. Insert 6 AAA alkaline batteries.
21
20
19
18
17
16
15
14
13
Note: If you need to install a tape cartridge, see "Inserting
a tape cartridge" below.
12
11
3. Replace the cover and snap it into place.
10
Optional AC adapter (APT0615Z1-1)
Warning: Make sure to use AC adapter APT0615Z1-1 or
damage may occur.
1. Plug one end of the AC adapter into the product.
2. Plug the other end of the AC adapter into the wall
outlet.
Inserting a tape cartridge
1. Remove any slack from the ink ribbon.
2. Remove the rear cover, if necessary.
3. Insert the tape cartridge and press it down firmly until
it snaps into place. If there is excess tape, feed the end
of the tape through the tape guide slot.
4. Replace the cover and snap it into place.
Preparing the tape
After inserting a tape cartridge, make sure to feed
some tape through the tape guide slot to position it
for printing.
1. Press
to turn on the product.
2. Press
+
3. Press the
Cut button to cut the tape.
.
or
to highlight a setting, then
or
to select setting options, then
.