Epson LABELWORKS LW-Z710 설치 매뉴얼 - 페이지 2

{카테고리_이름} Epson LABELWORKS LW-Z710에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson LABELWORKS LW-Z710 2 페이지.
Epson LABELWORKS LW-Z710에 대해서도 마찬가지입니다: 설치 매뉴얼 (2 페이지)

페이지 인쇄

Using the Printer

Printer Setup

1. Prepare the power supply.

You can use the printer by one of the two methods below.

Using batteries

Using the AC adapter

CAUTION

Always use AA-size alkaline dry cell batteries.

Always use the included AC adapter.

Remove the rubber guard.

Connect the included AC adapter

(AST1116Z2-1) to the printer, and plug the

Open the battery cover at the bottom of

power plug into a power outlet.

the printer.

Insert batteries.

Batteries: AA alkaline battery x 6

Close the battery cover.

Attach the rubber guard.

2. Inserting the tape cartridge in the printer

Place a tape cartridge in the printer as shown.

CAUTION

Always use dedicated tape cartridge having

Pass the end of the tape

through the gap.

the

symbol. Always perform the tape feed

operation after inserting a tape cartridge.

Remove any slack in the tape inside the

tape cartridge.

Use a pen or

a pencil.

Pull the tab to open the printer cover.

Close the printer cover.

Creating a label

1. Creating and printing a label

Using mobile device

Use the Epson application to create and print labels.

See the Epson website for more information.

U http://www.epson.com

Using Windows computer

Create labels with the label editing software "Label Editor" and print.

See the following manual for the procedure:

Label Editor User's Guide.

Troubleshooting

Meanings of lamps

The lamps indicate printer statuses.

Lamp's condition

* : Depends on printer operation status

--: Unlit

Fading in and out

Lit

Flashing quickly

Flashing

(once every 5 seconds)

Lit

Flashing quickly

This section describes all the procedures from printer setup to printing and attaching a label.

Connecting a Mobile Device

CAUTION

Connecting a Windows Computer

See "Downloading Printer Driver and Software" on the front side.

2. Attaching a label

Peel off the backing paper of the printed label to stick it onto an object.

Peel off the backing paper.

Backing paper

The shortest label you can create with this printer is approximately 22 mm

long.

When creating a label shorter than 22 mm long, cut the margins with scissors.

Printer status

Bluetooth enabled.

Or connected to an Android device or Windows computer.

Bluetooth connection completed. (when connecting to an iOS device)

Performing operation such as printing or label cutting.

Bluetooth disabled.

Power OFF.

Low batteries and need to be replaced. Have replacement batteries ready.

Replace batteries.

Printer error. Check the message displayed on the connected computer or the

mobile device.

1. Install the Epson applications.

See "Downloading Printer Driver and Software" on the front side.

2. Bluetooth connection setup (pairing)

CAUTION

Place your mobile device no more than one meter away from the printer

when making the settings.

MEMO

For Bluetooth pairing instructions, consult the documentation for your

mobile device.

Press the

button to turn the printer power ON.

If the Bluetooth function of the printer is disabled, enable it.

See "Enabling and Disabling the Bluetooth Function".

On your mobile device, turn on the Bluetooth feature and pair the

printer.

When pairing is complete, start the Epson application on the mobile device

to create labels.

1. Download necessary software and manuals

2 Install "Label Editor" and printer driver

Follow the on-screen instructions to install Label Editor.

When the printer driver installation screen appears, select "LW-Z710".

Select the connection method on the screen shown below.

USB

Connect the printer and the computer with a USB

cable following the instructions.

The printer driver for USB connection is

installed.

Attach the label and rub it firmly.

Problems not indicated by lamps

Printer power does not turn ON.

• Check that the power cable is connected properly, or that

batteries have been properly inserted. If the power still does not

turn ON, contact your place of purchase or the Epson Customer

Support Center.

• If a message is displayed on your computer or mobile device

screen, check the message information.

Unable to perform Bluetooth connection (pairing) with the

printer

• Check to see if the printer's

enable Bluetooth on the printer and then try performing the

operation. See "Enabling and Disabling the Bluetooth Function".

• Check that the printer communicating with another device.

If the printer is already communicating with one device, it is

unable to communicate with another device.

• If a message is displayed on your device screen, check the

message information.

Connection was interrupted during connection (pairing) with the

printer.

• Check to see if the printer's

enable Bluetooth on the printer and then try performing the

operation. See "Enabling and Disabling the Bluetooth Function".

• If the printer is connected to a computer with a USB cable

while the printer is communicating with a mobile device, the

communication with the mobile device is terminated. Terminate

the printer's connection to the computer, then redo the pairing

setting.

• If a message is displayed on your computer or mobile device

screen, check the message information.

Enabling and Disabling the Bluetooth Function

At the time of purchase, the Bluetooth function is set to be enabled when

you turn on the power of the printer. This can be switched between

enable and disable by button operation.

You can check the state of the Bluetooth function with the

See "Meanings of lamps".

If the power of the printer is on, press

the

button to turn off the power.

Press the

button and Bluetooth

button at the same time to turn on

the power of the printer.

You can switch alternately between enable

and disable by repeating the operations of

steps 1 and 2.

CAUTION

Do not connect the printer and computer before installing the software. Connect the

printer as directed in the installation screen.

MEMO

For information on how to turn on the Bluetooth feature of the computer, consult the

documentation for the computer.

Bluetooth®

Turn on the printer.

If the Bluetooth function of the printer is

disabled, enable it.

See "Enabling and Disabling the Bluetooth

Function".

Turn on the Bluetooth feature of

your computer.

The printer driver for Bluetooth connection is

installed.

When Finished Using Printer

When connecting the printer using Bluetooth

Press the

button to turn the printer power OFF.

Turn off Bluetooth on your device.

When using the AC adapter, unplug the power cable from the outlet and disconnect

the AC adapter plug from the printer.

When connecting the printer using a USB cable

Press the

button to turn the printer power OFF.

Disconnect the USB cable.

Unplug the power cable from the outlet, and disconnect the AC adapter plug from the printer.

When using the AC adapter, unplug the power cable from the outlet and disconnect

the AC adapter plug from the printer.

Auto power Off

The printer turns off automatically if it is not used within these time periods:

• 8 hours on AC power

• 20 minutes on battery power

Printer does not print when print operation is directed.

• If a message is displayed on your computer or mobile device

screen, check the message information.

• Check that connection cables are connected properly, that the

tape cartridge is mounted properly, and that the cover is closed

properly.

• Have you selected the printer to be used? Printing will not be

done properly if another printer is selected.

• Did you restart the computer after installing the printer driver?

lamp is fading in and out. If not,

The printer driver may not be installed correctly if the computer

was not restarted. Reinstall the printer driver.

Text is not printed properly.

Check that the tape cartridge is properly mounted.

Lines appear on printed labels.

The print head is dirty. Clean the print head. See "Cleaning".

Canceling a print job

Check the printer's power in ON, then press

of the printer briefly once.

Labels are not cut automatically

lamp is fading in and out. If not,

Is the cutter blade worn? Prolonged use of the cutter can wear

down and dull the blade. Contact the Epson Customer Support

Center.

lamp.

Select the checkbox as shown below.

Select the printer as shown below.

button on the front