Motorola H800 - Headset - Over-the-ear 빠른 시작 - 페이지 2

{카테고리_이름} Motorola H800 - Headset - Over-the-ear에 대한 빠른 시작을 온라인으로 검색하거나 PDF를 다운로드하세요. Motorola H800 - Headset - Over-the-ear 2 페이지. User manual
Motorola H800 - Headset - Over-the-ear에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (44 페이지)

페이지 인쇄

Motorola H800 - Headset - Over-the-ear 빠른 시작

Features and

Functions Guide

To turn your headset on, press the Call

button to extend the slider. The indicator

H800

light flashes blue (if paired with another

device), or is steadily blue (if ready to be

Slider

paired).

Bluetooth® Headset

To turn your headset off, push the slider

closed. The indicator light flashes blue three

times.

IMPORTANT:

Multi-Color

Be sure to first follow the

Indicator Light

Quick Start Guide

on the reverse side

of this guide

to complete initial setup

To prevent accidental headset operation, slide

of your H800.

the slider lock switch to the locked position.

European Union Directives

Function

Conformance Statement

Make a voice dial call

Hereby, Motorola declares that this

product is in compliance with:

• The essential requirements and

End a call

other relevant provisions of Directive

1999/5/EC.

Answer a call

• All other relevant EU Directives.

Ignore a call

Product

Redial last call

Approval

Number

The above gives an example of a typical Product

Approval Number.

Mute or unmute a call

You can view your product's Declaration of Conformity

(DoC) to Directive 1999/5/EC (to R&TTE Directive) at

www.motorola.com/rtte. To find your DoC, enter the

Note: Some features are phone/network dependent.

product Approval Number from your product's label in

the "Search" bar on the web site.

Note: Your H800 supports both Handsfree and Headset

Profiles. Accessing call functions depends upon which profile

your phone supports. See your phone's user's guide for more

information.

EARHOOKS AND YOUR

TURNING HEADSET

ON AND OFF

Your H800 headset is supplied with multiple size

earhooks. The earhook is attached onto a hinge pin,

and is placed onto your ear when using your

headset. To install an earhook on your headset:

Open the attached

earhook 90 degrees from

the headset.

Gently lift and pull the

Call

Slider Lock Switch

top of the earhook up

Button

(in locked position)

and off the upper hinge

pin. Then, pull it away to

remove it.

Position the headset for

right or left ear use (right

ear use is displayed).

Hook the bottom of the

Slider

earhook onto the lower

hinge pin, then lift and pull

the top of the earhook

over the upper hinge pin.

MAKING CALLS

Action

Function

Tap the Call button

Disable/Enable the

and speak the

indicator light

name after the tone

Tap the Call button

Answer a second

Tap the Call button

incoming call

Press and hold either

Volume button until

incoming call stops

End active call and

ringing

resume call on hold

Press and hold the

Call button for at least

Note: Resuming a call on hold is a phone-dependent feature.

2 seconds until you

If tapping the Call button does not execute action, revert to

hear a beep

the phone controls to resume call on hold.

Tap both Volume

Note: When indicator light is disabled, light does not display

buttons

for any headset function. Re-enable indicator light by pressing

and holding both Volume buttons at the same time while

powering on headset.

WEARING THE

HEADSET

Once you have attached your desired

earhook, follow these steps to wear your

headset on your ear:

Open the attached

earhook 45 degrees from

the headset.

Loop the earhook over

your ear.

1 Open Earhook

Press earhook to your ear.

2 Pull Earhook Up

When worn, your headset

will look like this on your

head:

Hinge Pin

INDICATOR LIGHTS

CONTINUED

With the Charger Plugged In

Action

Headset Indicator

Press and hold both

Red

Volume buttons at the

same time while

Yellow

powering on headset

Green

Tap the Call button

With No Charger Plugged In

Headset Indicator

Off

Tap the Call button

Three blue flashes

Steady blue

Rapid blue/purple flashes Pairing successful

Quick blue flash

Slow blue pulse

Slow blue flash

Slow red flash

Slow purple pulse

Quick red flash

Note: After 20 minutes on a call or of inactivity, the light stops

flashing to conserve power, but the headset remains on.

CHANGING VOLUME

BUTTON ORIENTATION

You can also change the orientation of the

volume buttons on your headset.

Turn the headset power off.

Press the Volume button you want to

assign as the "volume up" button and

press the Call button to extend the slider

(to power on the headset). The indicator

light flashes three times in blue.

Call

Button

AUDIO TONES

Audio Tone

Headset Status

Ascending tone

Powering on

Charging

Descending tone

Powering off

Charging 80% done

Two ascending

Pairing successful/

Charging complete

tones

Initiate voice dial

Ring tone

Incoming call

Headset Status

Two short tones when

Volume at minimum

pressing Volume button

or maximum

Power off

Powering on/off

High/low tones

Low battery

repeated every 60 sec.

Pairing mode

No audio indications;

Out of range

deteriorating quality

Incoming/outgoing call

Three ascending tones

Connected call/

Connected (on a call)

Redial last number

Standby (not on a call)

Three descending tones

Ended call

Idle (not connected

to phone)

Two rapid ascending

Mute enabled

tones

Connected call muted

Two rapid descending

Mute disabled

Low battery

tones

Volume

Buttons