Epson TM-T88IV ReStick 사용자 설명서 - 페이지 4

{카테고리_이름} Epson TM-T88IV ReStick에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson TM-T88IV ReStick 15 페이지. Receipt restick printer in windows using an ethernet connection
Epson TM-T88IV ReStick에 대해서도 마찬가지입니다: 브로셔 (2 페이지), 사양 (2 페이지), 사용자 설명서 (9 페이지), 기술 노트 (8 페이지), 단계별 설치 매뉴얼 (14 페이지), 기술 게시판 (5 페이지), 매뉴얼 (10 페이지), 사용자 설명서 (20 페이지)

페이지 인쇄

English

DIP Switch Tables

Serial Interface (DIP switch 1)

Function

1-1

Data receive error

1-2

Receive buffer

capacity

1-3

Handshaking

1-4

Data word length

1-5

Parity check

1-6

Parity selection

1-7

Transmission speed (See table below.)

1-8

Transmission speed

Transmission speed (bps)-bits per second

38400 *1

4800

9600

19200

Serial Interface (DIP switch 2)

Function

2-1

Handshaking

(BUSY condition)

2-2

Do not change

2-3

Print density/

2-4

Low power

2-5

Release condition

of receive buffer

BUSY (If receive

buffer capacity

set to 4 KB.)

2-6

Do not change

2-7

I/F pin 6 reset

2-8

I/F pin 25 reset

*1.

Only when DIP Switches 1-7 and 1-8 are on, the

transmission speed can be selected from one of

seven speeds: 2400, 4800, 9600, 19200, 38400, 57600,

and 15200 bps. The default is 38400.

OFF

Ignored

Prints "?"

45 bytes

4K bytes

XON/XOFF

DTR/DSR

7 bits

8 bits

Enabled

Disabled

Even

Odd

1-7

OFF

Receive buffer

Offline or

full

Receive buffer

full

See Table A

Releases BUSY

when remaining

receive buffer

capacity

reaches

138 bytes.

256 bytes.

Enabled

Disabled

Enabled

Disabled

Parallel Interface (DIP switch 1)

Function

1-1

Auto line feed

1-2

Receive buffer

capacity

1-3

Select paper

sensors to output

paper-end

signals (default

value of ESC C 3)

1-4

Error signal output

1-5~

Undefined

1-8

Parallel Interface (DIP switch 2)

Function

2-1

Handshaking

OFF

(BUSY condition)

OFF

2-2

Do not change

2-3

Print density/

2-4

Low power

2-5

Release condition

of receive buffer

BUSY (If receive

buffer capacity

set to 4 KB.)

2-6

Do not change

2-7

2-8

I/F pin 31 reset (Do not change)

Table A

Print density/low power

– Low power consumption mode

Print density "Normal"

Print density "Medium"

Print density "Dark"

OFF

Always

Always disabled

enabled

45 bytes

4K bytes

Disabled

Roll Paper end

sensor enabled,

Roll Paper near-

end sensor

enabled

Disabled

Enabled

OFF

Receive buffer

Offline or

full

Receive buffer

full

See Table A

Releases BUSY

when remaining

receive buffer

capacity

reaches

138 bytes.

256 bytes.

SW 2-3

SW 2-4

OFF