Epson TM-T88V 사용자 설명서 - 페이지 16

{카테고리_이름} Epson TM-T88V에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson TM-T88V 19 페이지. Pos printer
Epson TM-T88V에 대해서도 마찬가지입니다: 사양 (8 페이지), 브로셔 및 사양 (8 페이지), 사양 (2 페이지), 설정 지침 (2 페이지), 매뉴얼 (10 페이지), 매뉴얼 (4 페이지)

Epson TM-T88V 사용자 설명서
English

DIP Switch Tables

When using Serial Interface
DIP Switch Bank 1
SW
Function
1-1
Data receive error
1-2
Receive buffer
capacity
1-3
Handshaking
1-4
Data word length
1-5
Parity check
1-6
Parity selection
1-7
Transmission speed (See table A.)
1-8
DIP Switch Bank 2
SW
Function
2-1
Handshaking
(BUSY condition)
2-2
Do not change
settings
2-3
Print density
2-4
2-5
Release condition of
receive buffer BUSY
(If receive buffer
capacity set to 4KB.)
2-6
Do not change
setting.
2-7
I/F pin 6 reset
2-8
I/F pin 25 reset
Table A
Transmission speed (bps) bits per second
*1
38400
4800
9600
19200
*1: When DIP switches 1-7 and 1-8 are on, the transmission
speed can be selected from one of seven speeds:
2400, 4800, 9600, 19200, 38400, 57600, and 115200 bps
by control commands.
16 TM-T88V User's Manual
ON
OFF
Ignored
Prints "?"
45 bytes
4KB
XON/XOFF
DTR/DSR
7 bits
8 bits
Enabled
Disabled
Even
Odd
ON
OFF
Receive buffer
Offline or
full
Receive buffer
full
Fixed to OFF
See Table B
Releases BUSY
Releases BUSY
when remaining
when remaining
receive buffer
receive buffer
capacity
capacity
reaches
reaches
138 bytes.
256 bytes.
Fixed to OFF
Enabled
Disabled
Enabled
Disabled
SW1-7 SW1-8
ON
OFF
ON
OFF
When using Parallel Interface
DIP Switch Bank 1
SW
Function
1-1
Auto line feed
1-2
Receive buffer
capacity
1-3
Select paper sensors
to output paper-end
signals (default value
of a command) from
parallel I/F.
1-4
Error signal output
from parallel I/F
1-5~
1-8
DIP Switch Bank 2
SW
Function
2-1
Handshaking
(BUSY condition)
2-2
Do not change
settings
2-3
Print density
2-4
2-5
Release condition of
receive buffer BUSY
(If receive buffer
capacity set to 4KB.)
2-6
Do not change
2-7
setting.
2-8
I/F pin 31 reset
signal (Do not
change setting)
ON
Table B
ON
OFF
Print density/low power
OFF
Print density "Normal"
Print density "Medium"
Print density "Dark"
Do not set
ON
OFF
Always
Always disabled
enabled
45 bytes
4KB
Disabled
Roll paper end
sensor enabled,
Roll paper near-
end sensor
enabled
Disabled
Enabled
Undefined
ON
OFF
Receive buffer
Offline or
full
Receive buffer
full
Fixed to OFF
See Table B
Releases BUSY
Releases BUSY
when remaining
when remaining
receive buffer
receive buffer
capacity
capacity
reaches
reaches
138 bytes.
256 bytes.
Fixed to OFF
Fixed to ON
SW2-3
SW2-4
OFF
ON
OFF
ON
OFF
OFF
ON
ON