Epson 4880 - Stylus Pro Color Inkjet Printer 제품 정보 매뉴얼 - 페이지 4
{카테고리_이름} Epson 4880 - Stylus Pro Color Inkjet Printer에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 4880 - Stylus Pro Color Inkjet Printer 16 페이지. Ink fill for the refillable cartridge system
Epson 4880 - Stylus Pro Color Inkjet Printer에 대해서도 마찬가지입니다: 빠른 시작 설치 매뉴얼 (1 페이지), 네트워크 매뉴얼 (46 페이지), 설치 매뉴얼 (4 페이지), 제한 보증 (12 페이지), 사용 지침 (5 페이지)
페이지 인쇄
Epson Stylus Pro 4880
Error Messages
When a problem occurs, a message appears on the display and the lights on the control panel come on or flash.
Message/Light
CHANGE PAPER TYPE
COMMAND ERROR
DRIVER INK SET SETTING IS
WRONG
MISMATCH ERROR
Note:
These messages alternate.
FEED SHEET PAPER
FEED SHEET PAPER
MANUALLY
FORBIDDEN MEDIA FROM P.
TRAY
INK LOW
INVALID INK CRTG
LOAD PAPER
LOAD ROLL PAPER
LOAD SHEET PAPER IN
P. TRAY
LOWER INK LEVERS
LOWER L (or R) INK LVR
MNT REQ. nnnn
MNT TK NEAR FULL
MNT TNK FULL
4
Light
Explanation
Paper light on
Paper loaded does not match the
source selected.
—
You're using the wrong printer driver.
Damaged data was sent to the printer
or the data has an incorrect command.
The installed printer driver is not
correct for the printer.
—
The black ink cartridge option does
not match what is selected in the
driver.
Non-Epson genuine ink cartridge is
installed.
—
Cut sheet needs to be loaded
manually.
—
Cut sheet needs to be loaded
manually in the front or rear manual
feed slot.
B
Ink light flashing
Ink cartridge(s) are nearly expended
(printing continues).
B
Ink light on
You tried to install the wrong ink
cartridge.
Paper light on
Paper lever is in the released position
while loading paper.
Paper light on
Paper source setting in printer driver
is different from control panel.
—
One or both ink levers are raised.
—
A printer part (nnnn) will need to be
replaced soon.
—
The maintenance tank is almost full.
B
Ink light on
The maintenance tank is full.
Response
Press the
setting: either
for roll paper)
Press the
cancel the print job. Make sure you installed the
correct driver for your printer.
Press the
cancel the print job.
Stop printing, and press the
3 seconds. Then make sure that the installed printer
driver is correct for the printer.
Stop printing, and then press and hold the
button for 3 seconds. Select the correct black ink
cartridge option in the driver. If you want to continue
printing, press the
Press the
printing. If you want to continue printing, press the
pause button again.
Load the sheet in the front or rear manual feed slot.
Remove the cut sheet media from the paper tray and
load it in the correct slot.
Make sure you have replacement cartridges available;
you'll need to replace them soon.
If you are installing ink cartridges for the first time, you
must install the cartridges that came with your printer.
If you are replacing ink cartridges, check the package
and product code. Replace the cartridges with genuine
Epson ink cartridges.
After you finish loading paper, pull the paper lever all
the way forward, to the secured position.
Make sure the right paper is loaded and the paper
source setting is the same on the control panel and
printer driver.
Pull the lever or levers down to lock the ink cartridges.
Note the code number and contact Epson.
Although you can continue printing, you need to
replace the maintenance tank with a new one as soon
as possible. Make sure you have a replacement
maintenance tank on hand.
Replace the maintenance tank with a new one.
12/07
Paper Source button to select the correct
(for paper in the tray, or
.
pause button and hold it for 3 seconds to
pause button and hold it for 3 seconds to
pause button for
pause button.
pause button for 3 seconds to cancel
or
pause