Epson 755c - PowerLite XGA LCD Projector 부품 설명서 - 페이지 10

{카테고리_이름} Epson 755c - PowerLite XGA LCD Projector에 대한 부품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 755c - PowerLite XGA LCD Projector 26 페이지. Release of check tool for network projectors v1.00 for windows
Epson 755c - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 사양 시트 (2 페이지), 운영 매뉴얼 (47 페이지), 제품 지원 게시판 (30 페이지), 사용자 교체 가능 항목 (1 페이지), 빠른 설정 (2 페이지), 설치 매뉴얼 (19 페이지), 사용자 설명서 (1 페이지), 기능 설명서 (5 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (42 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

페이지 인쇄

Epson 755c - PowerLite XGA LCD Projector 부품 설명서

Epson PowerLite 755c/765c Projector

6. Hold down the

button on the remote control and use

Num

the numeric keypad to enter a 4-digit password.

The password will be

displayed as

. After you

****

enter the last digit, a

confirmation screen appears.

Enter the password again.

7. After you finish setting the

password, press the

button to exit.

8. Press the

button to

Num

deactivate the numeric

keypad.

Make a note of the password and keep it in a safe place.

Turning On the Password and User's Logo

To enable the password (and User's Logo, if one has been

created), follow these steps:

1. Press the

button on the remote control for about

Freeze

5 seconds until you see the Password Protect menu.

2. Select

Power ON Protect

3. Select

press

ON and

Esc

After turning on this feature, you have to unplug the

projector (not just turn it off) in order to activate it. The

password prompt appears only after plugging in the

projector and turning it on.

4. If you want to disable the password temporarily so someone

can use the projector without entering the password, select

and press

. Then hold down the

Timer

Enter

while you use the numeric keypad to enter the number of

hours (from 0 to 9999) you want the password feature

disabled. If you want the projector to request the password

every time it is turned on, set the timer to

The timer starts counting as soon as you close the Password

Protect menu. (You can check the elapsed time in this menu

next to

Time elapsed

When the period defined in the Time-elapsed setting has

passed, and the password is entered correctly, the elapsed

time is reset to

and the timer starts again. Remember to

disable or change this setting when you're finished using it.

Epson PowerLite 755c/765c Projector

Numeric keypad

Num button

and press

Enter

button

Num

5. To enable your User's Logo, select

press

. Then select

Enter

When this feature is on, the logo image appears when the

projector is turned on (if the

the Extended menu) and as the A/V Mute screen (if you

selected

as the

Logo

menu).

Note:

None of the User's Logo features can be changed when the User's

Logo Protect function is enabled.

6. Press

to close the Password Protect menu.

Starting the Projector with a Password

Note:

You must unplug the projector and then plug it back in to enable

password protection.

When the password function is enabled, you see this screen

when you plug in and turn on the projector:

Hold down the

Num

the numeric keypad buttons to enter the password. Once you

have entered the password correctly, the password screen closes,

and projection begins.

If the password is not correct, you see the message

password. Please try again

password three times in succession, you see the message

projector's operation will be locked. Request code xxxxx

and the projector switches to standby mode for approximately

5 minutes. Write down the request code. Then disconnect the

projector's power cord from the electrical outlet, reconnect it,

and turn the projector back on. When you see the Password

Protect Release screen, enter the correct password.

If you have forgotten the password, contact Epson for assistance

and give them the request code number that appears in the

Password Protect Release screen.

If you enter an incorrect password 30 times in a row, the

projector remains locked and you must contact an authorized

Epson servicer to unlock it.

8/05

User's Logo Protect

and press

Enter

Startup Screen

in the Extended

Background Color

button on the remote control as you use

. If you enter an incorrect

and

is enabled in

Wrong

The