Epson 7850p - PowerLite XGA LCD Projector 제품 정보 매뉴얼 - 페이지 16

{카테고리_이름} Epson 7850p - PowerLite XGA LCD Projector에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 7850p - PowerLite XGA LCD Projector 25 페이지. Release of check tool for network projectors v1.00 for windows
Epson 7850p - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 사용자 설명서 (12 페이지), 교체 부품 (1 페이지), 운영 매뉴얼 (47 페이지), 제품 지원 게시판 (30 페이지), 설치 매뉴얼 (5 페이지), 빠른 설정 (2 페이지), 브로셔 및 사양 (2 페이지), 기술 요약 (7 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (42 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

페이지 인쇄

Epson 7850p - PowerLite XGA LCD Projector 제품 정보 매뉴얼

12. Verify that you've enabled your computer's connection to

the access point. It should be listed as shown above, with

the small icon

next to it, indicating a connection.

If it's not listed, click

Configure

your access point.

13. When done, click

. Continue with "Projecting

Wirelessly" on page 15.

Checking the Gateway IP Address

If you're entering IP addresses manually in Access Point mode

and need to find out the gateway IP address (the IP address of

your access point), make sure the wireless connection to the

access point is currently active, as described in the previous

section.

Note: If you can't identify the gateway address using this

Windows utility, use the administrator's utility software that

came with your access point.

1. Access your wireless network Properties window. For

example, in Windows XP click

Network and Internet Connections

double-click the

Network Connections

2. Right-click the

Wireless Network Connection

select

. Then click the

Status

The gateway's (access point's) IP address is listed as shown:

Projecting Wirelessly

Once you've started EasyMP and set up your projector and

computer in either Ad Hoc mode or Access Point mode,

follow these steps to start NS Connection and project

wirelessly.

Note: You must have installed EMP NS Connection from your

projector CD-ROM. See the User's Guide for installation

instructions.

1. Make sure you've inserted the EPSON 802.11b card in the

projector's card slot (see page 11). Then select

from the Windows Start menu.

Connection

and then type the name of

Start > Control Panel >

. Then

icon.

icon and

tab.

Support

Gateway

address

EMP NS

EPSON PowerLite 7850p Projector

The first time you start NS Connection, you see a dialog

box asking you to select your network. Select the IP address

for your computer's network adapter card and click

Note: If you don't see your network adapter's IP address,

allow a minute for it to appear. If your access point uses

DHCP, sometimes it takes a minute for the server to pick up

the IP address.

You see the screen below. (If you have previously started

NS Connection, this is the first screen you see.)

Note: Once you've selected the IP address for your network

adapter, you won't see the Switch network dialog box when

you start NS Connection. If you want to change to a different

network adapter, click

Connection dialog box, then click

If the connection is working properly, you see your

projector listed. If you have additional projectors on the

network, they are also listed, along with their status. The

color of the status icon next to each projector's name

indicates its status:

❏ Gray: the projector is not connected

❏ Orange: the projector is connected to another

computer

❏ Green: the projector is connected to your computer

6/03

EPSON PowerLite 7850p Projector

on the EMP NS

Extension

Switch LAN