Epson 7850p - PowerLite XGA LCD Projector 제품 지원 게시판 - 페이지 8

{카테고리_이름} Epson 7850p - PowerLite XGA LCD Projector에 대한 제품 지원 게시판을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 7850p - PowerLite XGA LCD Projector 25 페이지. Release of check tool for network projectors v1.00 for windows
Epson 7850p - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 사용자 설명서 (12 페이지), 교체 부품 (1 페이지), 운영 매뉴얼 (47 페이지), 제품 지원 게시판 (30 페이지), 설치 매뉴얼 (5 페이지), 빠른 설정 (2 페이지), 브로셔 및 사양 (2 페이지), 제품 정보 매뉴얼 (25 페이지), 기술 요약 (7 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (42 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

Epson 7850p - PowerLite XGA LCD Projector 제품 지원 게시판
EPSON
Date:
10/18/2004
PSB.2004.10.005
PSB #:
Reference:
N/A
PowerLite 7800p / 7800NL / 7850p / 7850NL
Product(s):
Proper Selection Of RGB Video
Subject:
This bulletin was created to inform you of an issue that can occur when a PC is connected to a
PowerLite 7800p / 7850p 15 pin VGA "Computer" port with the input mode set to "RGB-Video."
The image is displayed, but all 4 sides are clipped. No amount of adjustments on the PC or
the projector settings can fix the screen.
Reason:
The PowerLite 7800p/7850p has 2 video input signal modes for the 15 pin VGA "Computer"
connector. The two signal modes are "Analog-RGB" and "RGB-Video." To connect a PC to
the 15 pin VGA connector, be sure that you have selected "Analog-RGB" as the signal mode.
Refer to page 72 of the PL-7800p User's Guide or page 133 of the PL-7850p User's Guide for
more information on customizing projector features.
If you have selected "RGB-Video" you will see clipping on all four sides of the displayed image.
There are 2 ways to change the input signal mode. The easiest method is to repeatedly press
the "Comp" button on the remote control until "Computer (Analog-RGB)" is displayed in the
upper right corner. To toggle the input signal mode you must press the button while the source
message is still displayed in the upper right corner. This will correct the clipping issue.
Notes:
1. If you do not see a message in the upper right corner go to the projector's menu, and
navigate to the "Setting" menu and set "Message" to "On."
2. Do not use the projector's control panel with this method.
The second method is to use the projector's menus. Bring up the projector's menu by pressing
the "Menu" button on the projector's control panel, or on the remote control. Then using the
arrow buttons, navigate to the "Setting" menu, press enter, and arrow down to "Computer
Input" and press enter. Select "Analog-RGB" and press enter. When you exit the menu
system, the displayed image will appear without any clipping.
The BNC Input connector also has 4 input signal modes including the two signal modes of
"Analog-RGB" and "RGB-Video." To connect a PC to the BNC connector, be sure that you
have selected "Analog-RGB" just like the 15 pin VGA "Computer" connector. You can use the
same methods described above for changing the BNC Input signal modes, just substitute
"BNC" for "Computer."
Note: Connection of a PC to the BNC Input is seldom used, as it requires a special cable.
Normal display of a PC connected to the 15 pin VGA connector with "Analog-RGB" as the
signal mode.
P
S
RODUCT
UPPORT
B
ULLETIN
Page 1 of 3
PSB.2004.10.005
Originator: TC
Authorization:
Total Pages: 3