Epson 7900p - PowerLite XGA LCD Projector 제품 정보 - 페이지 9

{카테고리_이름} Epson 7900p - PowerLite XGA LCD Projector에 대한 제품 정보을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 7900p - PowerLite XGA LCD Projector 24 페이지. Supplemental / late breaking information
Epson 7900p - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 교체 부품 (1 페이지), 빠른 설정 (2 페이지), 사용자 설명서 (1 페이지), 기술 요약 (7 페이지), 제품 지원 게시판 (7 페이지), 렌즈 설치 (5 페이지)

Epson 7900p - PowerLite XGA LCD Projector 제품 정보
Adjusting the Color Mode
You may want to adjust the color mode to select a setting
that is appropriate for the image you're projecting and the
environment in which you're projecting it.
The following table lists the available color modes.
Color mode
Description
For matching the color palette of standard sRGB
sRGB
computer displays.
For increased brightness in bright rooms (the
Dynamic
default for non-computer display).
For computer presentations (the default when
Presentation
projecting from a computer with analog video).
For optimizing movie images with increased
Theater
contrast.
For increased brightness when playing video
Living Room
games or watching TV in a bright room.
To change the color mode, press the
the remote control until you see the mode you want. The
currently selected setting appears in the upper right corner of
the screen. You can also use the projector menu system to select
the Color Mode in the Video menu.

Projecting Images Without a Screen

Even if you don't have a screen, you can project images onto
surfaces like blackboards and colored walls without loss of
image color. Your projector has a sensor that measures the
conditions of the projection surface and automatically adjusts
the colors and shading of your image.
Making Initial Color Corrections
Press the
button on
Wall Shot
either the remote control or the
projector's control panel while
projecting an image.
Wall Shot's status appears in the
upper right corner of your screen.
Then you see a sequence of colors
flash for approximately five
seconds while the sensor measures
the conditions of the projection
surface and adjusts the image.
Note: If the status message indicates
that Wall Shot is off, press the
it on.
button on
Color Mode
Wall Shot ON
button again to turn
Wall Shot
Epson PowerLite 7900p Projector
When you turn off the projector, it stores the correction values
obtained by the last Wall Shot measurements. This is useful if
you're projecting against the same surface and under the same
conditions. To retrieve these corrections, just press the
button again while projecting an image.
Shot
Adjusting Color Corrections for a New
Surface
Follow these steps to adjust the correction values if you're
projecting on a new surface or in a new location:
1. Press the
Wall Shot
projector while you're projecting an image. Wait for the
Wall Shot status screen.
2. Press the
Wall Shot
on the status screen.
Readjustment
You see a sequence of colors flash for about five seconds as
the projector adjusts the color correction values for the new
projection surface.

Shutting Down the Projector

When you've finished using the projector, follow the
recommended procedure below to shut it down. This extends
the life of the lamp and protects the projector from possible
overheating.
Note: When the projector has not received any input signals for 30
minutes, it automatically turns off the projector lamp and enters
sleep mode. This conserves electricity, cools the projector, and
extends the life of the lamp. If you are done using the projector,
unplug the power cord. If you want to start projecting again, press
the P
button.
Power
You can turn off sleep mode using the
Setting menu. If
Standby Mode
(in the Advanced1 menu), the lamp turns off but the projector
does not go into full sleep mode. (It provides enough operation to
allow network access.)
Follow these steps to turn off the projector:
1. Turn off any equipment plugged into the projector.
2. To turn off the projector, press the red P
the projector or remote control.
You see a confirmation
message. (If you don't want
to turn it off, press any
other button.)
9/04
button on the remote control or
button until you see
Wall Shot
Sleep Mode
has been set to
Power
Epson PowerLite 7900p Projector
Wall
option in the
Network ON
button on
9
-