Epson 821p - PowerLite XGA LCD Projector 제품 정보 - 페이지 10

{카테고리_이름} Epson 821p - PowerLite XGA LCD Projector에 대한 제품 정보을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 821p - PowerLite XGA LCD Projector 15 페이지. Release of emp ns connection for windows & mac upgrade from v2.50 to v2.51
Epson 821p - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 사양 (2 페이지), 운영 매뉴얼 (47 페이지), 부품 목록 (1 페이지), 빠른 설정 (2 페이지), 사용자 설명서 (1 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (8 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

Epson 821p - PowerLite XGA LCD Projector 제품 정보
Epson PowerLite 821p Projector

Starting the Projector with a Password

Caution:
If you lose the remote control, you will not be able to enter the
password; so keep the remote control in a safe place at all times.
When the password function is enabled, you see this screen
when you turn on the projector:
Hold down the
button on the remote control as you use
Num
the numeric keypad buttons to enter the password. Once you
have entered the password correctly, the password screen closes,
and projection begins.
If the password is not correct, you see the message
password. Please try again
password three times in succession, you see the message
projector's operation will be locked. Request code xxxxx
and the projector switches to standby mode for approximately 5
minutes. Write down the request code. Then disconnect the
projector's power cord from the electrical outlet, reconnect it,
and turn the projector back on. When you see the Password
Protect Release screen, enter the correct password.
If you have forgotten the password, contact Epson for assistance
and give them the request code number that appears in the
Password Protect Release screen.
If you enter an incorrect password 30 times in a row, the
projector remains locked and you must contact an authorized
Epson servicer to unlock it.

Disabling the Projector's Buttons

When you enable the Operation Lock function, all the
projector's buttons are disabled except for the P
Follow these steps to disable the projector's buttons:
1. Press the
button.
Menu
2. Select the
menu and press
Setting
3. Select
Operation Lock
4. Select
and press
ON
Enter
to confirm the setting.
5. Press the
button to exit the menu system.
Menu
Note:
You can cancel Operation Lock by pressing the projector's
button for 7 seconds.
10
Epson PowerLite 821p Projector
-
Wrong
. If you enter an incorrect
Power
.
Enter
and press the
button.
Enter
. Then select
and press
Yes

Projector Status Lights

The lights on top of the projector indicate the projector's status
and let you know when a problem occurs.
Power light
Lamp light
Temperature
light
If the projector is not working correctly, first turn it off and
unplug it. Then plug the power cord back in and turn on the
projector. If this does not solve the problem, check the status
lights on top of the projector and try the solutions
recommended in the following table.
The
Power
light
Flashing
green
Green
Flashing
orange
Orange
Red
button.
Flashing
red
Enter
Red
Enter
9/04
Lamp
Temp
light
light
Description
Off
Off
The projector is warming up.
Off
Off
The projector is operating
normally.
Off
Off
The projector is cooling down.
Wait for the light to stop
flashing before unplugging it.
Off
Off
The projector is in sleep
mode. Unplug it or press the
Power button to turn it on.
P
Off
Red
The projector has overheated
and turned itself off. Let it cool
for 5 minutes, then turn it back
on. Make sure there is space
around and under the projector
for ventilation. Also, clean the
air filter and vents. If it still
overheats, replace the filter.
Off
Flashing
The projector is too hot. Clean
orange
the air filter and vents and
make sure there is plenty of
space for ventilation. Room
temperature should not exceed
90 °F.
Off
Flashing
There is a problem with the fan
red
or sensor. Unplug the projector
and contact Epson.