Epson 890N - FX B/W Dot-matrix Printer 제품 정보 매뉴얼 - 페이지 8

{카테고리_이름} Epson 890N - FX B/W Dot-matrix Printer에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 890N - FX B/W Dot-matrix Printer 19 페이지. Impact printers
Epson 890N - FX B/W Dot-matrix Printer에 대해서도 마찬가지입니다: 사용자 설명서 (48 페이지), 매뉴얼 (11 페이지), 사양 (2 페이지), 기술 요약 (7 페이지)

페이지 인쇄

Epson 890N - FX B/W Dot-matrix Printer 제품 정보 매뉴얼

Control Panel Buttons and Lights

Button/Light

Function

Font button

Selects one of the fonts. See "Selecting a

Font and Pitch" on page 8.

Font lights

Indicate which font is selected.

Reset

When you press both the Font and Pitch

buttons simultaneously, the printer clears the

buffer and restores its default settings.

Pitch button

Selects one of the pitch settings. See

"Selecting a Font and Pitch" on page 8.

Pitch lights

Indicate which pitch is selected.

Tear Off/Bin

Feeds continuous paper forward to the

button

tear-off position.

Feeds continuous paper backward from the

tear-off position to the top-of-form position.

Selects a cut-sheet feeder bin when the

cut-sheet feeder is installed.

Tear Off/Bin

Both flash when continuous paper is in the

lights

tear-off position.

Both off when continuous paper is not in the

tear-off position or when bin 1 of the optional

cut-sheet feeder is selected.

Left light is on when Card mode is selected.

Right light is on when bin 2 of the optional

cut-sheet feeder is selected.

When you press the Pitch and Tear Off/Bin

buttons at the same time, the printer enters

the default setting mode. See "Changing the

Default Settings" on page 14.

Set

In default setting mode, you can press the

Tear Off/Bin button to select a value.

Load/Eject button Loads a single sheet of paper.

Ejects a single sheet of paper.

Loads continuous paper from the standby

position.

Feeds continuous paper backward to the

standby position if a sheet is loaded.

Micro Adjust

When you hold down the Pause button for

three seconds, the printer enters the Micro

Adjust mode. In this mode, you can press the

LF/FF

the top-of-form or tear-off position. See

"Using the Micro Adjust Function" on

page 11.

and Load/Eject

buttons to adjust

LF/FF button

Pause light

Pause button

Paper Out light

Lock function

Power-on Functions

The table below summarizes the power-on functions available

through the control panel. To perform the function on the

right, hold down the button(s) on the left while you turn on the

printer.

Control panel button

Load/Eject

LF/FF

Load/Eject + LF/FF

Load/Eject + LF/FF + Pause

Pause

Load/Eject + Pause

LF/FF + Pause

Font + Pitch

Pitch + Pause

Font + Tear Off/Bin

Tear Off/Bin + Pause

Tear Off/Bin + Load/Eject

Font + Pitch + Tear Off/Bin

6/03

EPSON FX-890/FX-2190

Feeds paper line by line when pressed

quickly.

Ejects a single sheet or advances continuous

paper to the next top-of-form position when

held down.

On when the printer is paused.

Flashes when the printer is in Micro Adjust

mode.

Stops printing temporarily, and resumes

printing when pressed again.

When held down for three seconds, enters

the Micro Adjust mode. When pressed again,

exits the Micro Adjust mode.

On when no paper is loaded in the selected

paper source or paper is not loaded correctly.

Flashes when paper has not been fully

ejected or paper is jammed.

When Lock-out mode is on, the Paper Out

and Pause lights flash if a locked button is

pressed. See the Reference Guide for more

information.

Function

NLQ self test

Draft self test

Data (Hex) dump

EEPROM reset

Bidirectional adjustment mode

Control panel Lock-out mode (on/off)

Default settings for control panel

Lock-out mode

Quiet mode

Copy mode

Default setting, simple mode

Okidata ML 320T/321T mode

Reset the Driving Line count for ribbon

change timing

Program reload mode

EPSON FX-890/FX-2190