Epson C11C524025 - FX 890 - Printer 제품 정보 매뉴얼 - 페이지 15
{카테고리_이름} Epson C11C524025 - FX 890 - Printer에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson C11C524025 - FX 890 - Printer 19 페이지. Impact printers
Epson C11C524025 - FX 890 - Printer에 대해서도 마찬가지입니다: 사용자 설명서 (48 페이지), 매뉴얼 (11 페이지), 사양 (2 페이지), 기술 요약 (7 페이지)
페이지 인쇄
EPSON FX-890/FX-2190
Clearing Paper Jams
Follow these steps to clear a paper jam:
1. Turn off the printer and open the printer cover.
2. If continuous paper is jammed in the printer, tear off the
fresh supply at the perforation nearest the paper entry slot.
3. Turn the knob on the left side of the printer away from you
to remove the paper in the printer. Remove any remaining
pieces of paper.
4. If the paper is stuck where the printer ejects it, gently pull
the paper out of the printer.
Caution: Use the knob on the left side of the printer to clear
paper jams only when the printer is off. Otherwise, you may
damage the printer or change the top-of-form or tear-off
position.
5. Close the printer cover and turn on the printer. Make sure
the
light is not flashing and the
Paper Out
off.
Changing the Default Settings
While you can often change the printer's settings through your
software or printer driver, you may sometimes need to change
one or more of the printer's default settings. There are two ways
to do this:
Using the EPSON Remote Configuration Manager on the
printer software CD-ROM. (See the User's Guide for more
information.)
From the printer's control panel using the default-setting
mode.
For instructions on using the Remote Configuration Manager,
see the PDF manual on the CD-ROM. To use the control
panel, see below. For detailed information about default
settings, see the Reference Guide.
14 - EPSON FX-890/FX-2190
The following table shows the options available for each printer
setting.
Setting
Skip over perforation
Auto tear-off
Auto line feed
Print direction
Software
I/F (interface) mode
Auto I/F (interface)
wait time
Parallel I/F
bidirectional mode
Packet mode
0 slash
Buzzer
light is
Pause
Auto CR (available in
IBM PPDS emulation
mode)
IBM character table*
Page length for front
tractor
Page length for rear
tractor
Character table
International character
set for italic table
(options depend on
country)
Manual feed wait
time
6/03
Options (default in bold)
Off, On
Off, On
Off, On
Bi-D, Uni-D
ESC/P, IBM PPDS
Auto, Parallel, USB, Option
10 seconds, 30 seconds
Off, On
Off, Auto
0,
(the zero character with a slash)
Off, On
Off, On
Table 2, Table1
Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8, 8.5,
11, 70/6, 12, 14, 17
Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8, 8.5,
11, 70/6, 12, 14, 17
Standard model: italic, PC 437, PC 850,
PC 860, PC 863, PC 865, PC 861, BRASCII,
Abicomp, Roman 8, ISO Latin 1, PC858,
ISO8859-15
All other models: Italic, PC 437, PC 850, PC
437 Greek, PC 853, PC855, PC 852, PC 857,
PC 866, PC 869, MAZOWIA, Code MJK, ISO
8859-7, ISO Latin 1T, Bulgaria, PC 774,
Estonia, ISO 8859-2, PC 866 LAT., PC 866
UKR, PC-APTEC, PC708, PC720, PC-AR864,
PC 860, PC 865, PC 861, PC 863, BRASCSII,
Abicomp, Roman 8, ISO Latin 1, PC858,
ISO8859-15, PC771, PC437 Slovenia,
PC MC, PC1250, PC1251
Italic U.S.A., Italic France, Italic Germany,
Italic U.K., Italic Denmark 1, Italic Sweden,
Italic Italy, Italic Spain 1
1 second, 1.5 seconds, 2 seconds,
3 seconds